2GR-FKS (FUEL): FUEL INJECTOR (for Direct Injection): REMOVAL; 2018 - 2020 MY Camry [06/2017

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM1000000015IJI
Model Year Start: 2018	Model: Camry	Prod Date Range: [06/2017 - 10/2020]
Title: 2GR-FKS (FUEL): FUEL INJECTOR (for Direct Injection): REMOVAL; 2018 - 2020 MY Camry [06/2017 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel injector assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
*: When performing learning using the Techstream. Click here
Battery terminal is disconnected/reconnected	Perform steering sensor zero point calibration	Lane departure alert system (w/ Steering Control)
		Pre-collision system
		Intelligent clearance sonar system*
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system
Replacement of fuel injector assembly (for Port Injection) Replacement of fuel injector assembly (for Direct Injection) Replacement of throttle body with motor assembly Cleaning the deposits from the throttle body with motor assembly	Inspection after repair	Poor idle, etc. Engine start function, etc.

CAUTION:

Never perform work on fuel system components near any possible ignition sources.
Vaporized fuel could ignite, resulting in a serious accident.
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.

PROCEDURE

1. REMOVE FUEL (ENGINE ROOM SIDE) PUMP ASSEMBLY (for High Pressure)

Click here

2. REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY

CAUTION:

To prevent serious injury due to fuel spray from the high-pressure fuel lines, always discharge fuel system pressure before removing any fuel system components.

(a) Using a 17 mm union nut wrench, loosen the 2 union nuts of the No. 2 fuel pipe sub-assembly.

(b) Remove the No. 2 fuel pipe sub-assembly from the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH.

3. REMOVE WIRE HARNESS CLAMP BRACKET

(a) Disconnect the No. 6 engine wire connector and No. 7 engine wire connector.

(b) Disengage the 2 clamps to remove the wire harness clamp bracket.

4. REMOVE FUEL DELIVERY PIPE WITH SENSOR ASSEMBLY LH

(a) Disconnect the fuel pressure sensor connector.

(b) Remove the bolt.

(d) Remove the 2 bolts, 2 nuts and fuel delivery pipe with sensor assembly LH with the 3 fuel injector assemblies from the cylinder head LH.

	Bolt
	Nut

NOTICE:

If fuel intrudes into the combustion chamber, there may be adverse affects to the engine main body.
Make sure not to touch or strike the tips of the fuel injector assemblies.
Pull and remove the fuel delivery pipe with sensor assembly LH in a straight line without tilting it.

(e) Disconnect the 3 fuel injector assembly connectors.

5. REMOVE FUEL DELIVERY PIPE RH

(a) Remove the bolt.

(b) Disengage the clamp to disconnect the No. 6 engine wire from the fuel delivery pipe RH.

(c) Remove the 2 bolts, 2 nuts and fuel delivery pipe RH with the 3 fuel injector assemblies from the cylinder head sub-assembly.

	Bolt
	Nut

NOTICE:

If fuel intrudes into the combustion chamber, there may be adverse affects to the engine main body.
Make sure not to touch or strike the tips of the fuel injector assemblies.
Pull and remove the fuel delivery pipe RH in a straight line without tilting it.

(d) Disconnect the 3 fuel injector assembly connectors.

6. REMOVE FUEL INJECTOR ASSEMBLY

(a) Secure the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH in a vise between aluminum plates and pull out the 6 fuel injector assemblies.

NOTICE:

Pull and remove each fuel injector assembly in a straight line to avoid damaging the seal surface of the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH O-ring.
After removing the fuel injector assemblies, remove any O-rings, No. 1 fuel injector back-up rings and No. 3 fuel injector back-up rings remaining on the fuel delivery pipe with sensor assembly LH and fuel delivery pipe RH side.
Attach a tag or label with the corresponding cylinder number to each fuel injector assembly so that they can be installed to their original locations.

(b) Remove the nozzle holder clamp from each fuel injector assembly.

NOTICE:

Do not damage the area that contacts the O-ring.

(d) Remove the O-ring and No. 1 fuel injector back-up ring from each fuel injector assembly.

(e) Remove the C-ring and injector vibration insulator from each fuel injector assembly.

7. REMOVE FUEL INJECTOR SEAL

(a) Using the tip of needle nose pliers, pinch and pull the fuel injector seal at several points to stretch it.

NOTICE:

Excessively pinching the fuel injector seal may damage the groove of the fuel injector assembly.
If a fuel injector assembly is dropped or the tip of the fuel injector assembly is struck, replace it with a new one.

(b) Remove the fuel injector seal from each fuel injector assembly.