Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM10000000155V9
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 - 10/2020]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/o Electric Parking Brake System): C146E; Open in ABS Solenoid Relay Circuit; 2018 - 2020 MY Camry [06/2017 - 10/2020]

DTC

C146E

Open in ABS Solenoid Relay Circuit

DESCRIPTION

The ABS solenoid relay is built into the skid control ECU in the brake actuator assembly. The ABS solenoid relay supplies power to the ABS and TRAC solenoids. The skid control ECU (brake actuator assembly) detects an ABS solenoid relay malfunction by performing a self check and relay operation check.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C146E

Open in ABS Solenoid Relay Circuit

Either of the following is detected:

  1. The ABS solenoid relay drive circuit in the skid control ECU (brake actuator assembly) is malfunctioning.
  2. The ABS solenoid relay cannot be switched between on and off.
  • ABS NO. 2 fuse
  • ABS solenoid relay circuit
  • ABS solenoid relay (brake actuator assembly)

DTC Detection Conditions: C146E

 

Vehicle Condition

Pattern 1

Pattern 2

Diagnosis Condition

-

-

-

Malfunction Status

The ABS solenoid relay drive circuit in the skid control ECU (brake actuator assembly) is malfunctioning.

-

The ABS solenoid relay cannot be switched between on and off.

-

Detection Time

-

-

Number of Trips

1 trip

1 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the skid control ECU (brake actuator assembly), perform system variant learning and acceleration sensor zero point calibration.

    Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/o Electric Parking Brake System): CALIBRATION

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

1.

REPLACE BRAKE ACTUATOR ASSEMBLY

(a) Replace the skid control ECU (brake actuator assembly).

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: BRAKE ACTUATOR: REMOVAL

HINT:

This DTC is output when the skid control ECU (brake actuator assembly) detects a malfunction in an internal circuit.

(b) Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Utility / Test Mode.

(c) Perform system variant learning and acceleration sensor zero point calibration.

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/o Electric Parking Brake System): CALIBRATION

Chassis > ABS/VSC/TRAC/EPB > Utility

Tester Display

Test Mode

(d) Enter the following menus: Chassis / ABS/VSC/TRAC/EPB / Utility / Signal Check.

(e) Perform the sensor check using the Test Mode (Signal Check) procedure.

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/o Electric Parking Brake System): TEST MODE PROCEDURE

Chassis > ABS/VSC/TRAC/EPB > Utility

Tester Display

Signal Check

NEXT

END