| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM10000000155SO |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [06/2017 - 10/2020] |
| Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/ Electric Parking Brake System): HOW TO PROCEED WITH TROUBLESHOOTING; 2018 - 2020 MY Camry [06/2017 - 10/2020] | ||
|
HOW TO PROCEED WITH TROUBLESHOOTING |
CAUTION / NOTICE / HINT
HINT:
*: Use the Techstream.
PROCEDURE
|
1. |
VEHICLE BROUGHT TO WORKSHOP |
|
|
2. |
CUSTOMER PROBLEM ANALYSIS |
(a) Interview the customer and confirm the problem.
Click here
![2018 MY Camry [06/2017 - 08/2018]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
|
|
3. |
CHECK DTC AND FREEZE FRAME DATA* |
(a) Check and record DTCs and Freeze Frame Data.
for DTC Check / Clear: Click here
for Freeze Frame Data: Click here
Chassis > ABS/VSC/TRAC/EPB > Trouble Codes
(b) Clear the DTCs and Freeze Frame Data.
for DTC Check / Clear: Click here
for Freeze Frame Data: Click here
Chassis > ABS/VSC/TRAC/EPB > Clear DTCs
(c) Reconfirm the DTCs.
(1) Reconfirm the DTCs based on the recorded DTCs and Freeze Frame Data.
for DTC Check / Clear: Click here
for Freeze Frame Data: Click here
Chassis > ABS/VSC/TRAC/EPB > Trouble Codes
HINT:
-
When CAN communication system DTCs are output, repair the CAN communication system first.
Click here
-
If DTC U0100, U0123 and/or U0126 are among the CAN communication DTCs that are output, first use the Data List to check for a momentary open circuit.
Click here
-
If the Techstream cannot communicate with the skid control ECU (brake actuator assembly), inspect the CAN communication system.
Click here
-
If there is no response from the skid control ECU (brake actuator assembly), inspect the +BS circuit of the skid control ECU (brake actuator assembly).
Click here
|
Result |
Proceed to |
|---|---|
|
DTCs are output. |
A |
|
DTCs are not output. (Problem symptom does not occur.) |
B |
|
DTCs are not output. (Problem symptom occurs.) |
C |
| B |
|
| C |
|
|
|
4. |
DIAGNOSTIC TROUBLE CODE CHART |
(a) Proceed to Diagnostic Trouble Code Chart.
Click here
| NEXT |
|
|
5. |
SYMPTOM SIMULATION |
(a) Proceed to How to Proceed with Troubleshooting.
Click here
|
|
6. |
PROBLEM SYMPTOMS TABLE |
(a) Proceed to Problem Symptoms Table.
Click here
|
|
7. |
CIRCUIT INSPECTION* |
|
|
8. |
IDENTIFICATION OF PROBLEM |
|
|
9. |
REPAIR OR REPLACEMENT |
|
|
10. |
RECONFIRM DTC* |
(a) Clear the DTCs.
Click here
Chassis > ABS/VSC/TRAC/EPB > Clear DTCs
(b) Check if the same DTCs are output.
Click here
Chassis > ABS/VSC/TRAC/EPB > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTCs are not output. |
A |
|
DTCs are output. |
B |
| B |
|
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS
|
|
|
11. |
CONFIRMATION TEST* |
| NEXT |
|
END |
|
|