Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM10000000155EE
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 - 08/2018]
Title: 2GR-FKS (LUBRICATION): OIL PUMP: REMOVAL; 2018 MY Camry [06/2017 - 08/2018]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during oil pump removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*1

Memorize steering angle neutral point

Parking Assist Monitor System

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

Replacement of ECM

Vehicle Identification Number (VIN) registration

MIL comes on

2018 - 2024 MY Camry [06/2017 -        ]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: REGISTRATION

ECU communication ID registration (Immobiliser system)

Engine start function

2018 - 2019 MY Camry [03/2017 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

  • Replacement of throttle body with motor assembly
  • Cleaning the deposits from the throttle body with motor assembly
  • Replacement of fuel injector assembly (for port injection)
  • Replacement of fuel injector assembly (for direct injection)
  • Replacement of fuel pump assembly (for high pressure side)
  • Replacement of ignition coil assembly
  • Air leaks from intake system
  • Gas leak from exhaust system is repaired
  • Replacement of knock control sensor

Inspection After Repair
  • Poor idle, etc.
  • Engine start function, etc.

2018 MY Camry [06/2017 - 08/2018]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

Replacement of automatic transaxle assembly
  1. Reset memory
  2. Input transaxle compensation code into ECM
  3. Perform road test to allow ECM to learn
  • Large shift shock
  • Deterioration of fuel efficiency

2018 MY Camry [06/2017 - 08/2018]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: INITIALIZATION for Initialization

2018 - 2024 MY Camry [06/2017 -        ]; UA80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: REGISTRATION for Registration

Replacement of ECM

(If possible, read the transaxle compensation code from the previous ECM)
  1. Reset memory*2
  2. Transfer transaxle compensation code
  3. Perform road test to allow ECM to learn

Replacement of ECM

(If impossible, read the transaxle compensation code from the previous ECM)
  1. Reset memory*2
  2. Reset transaxle compensation code
  3. Perform road test to allow ECM to learn

Replacement of ECM

Code registration (Smart key System (for Start Function))
  • Wireless door lock control system
  • Smart key system (for Entry Function)
  • Smart key system (for Start Function)
  • Steering lock function

2018 - 2019 MY Camry [03/2017 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

Rear television camera assembly optical axis (Back camera position setting)

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION for Initialization

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: CALIBRATION for Calibration

Replacement of front bumper assembly

Front television camera view adjustment

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION for Initialization

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: CALIBRATION for Calibration

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)
  • Television camera controller initialization
  • Adjust steering angle
  • Rear television camera assembly optical axis (Back camera position setting)

Front wheel alignment adjustment

Perform system variant learning and acceleration sensor zero point calibration.
  • VSC disabled or malfunctioning
  • DTCs are output
  • Slip indicator light illuminated
  • ABS warning light illuminated

2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/ Electric Parking Brake System): CALIBRATION

  • *1: When performing learning using the Techstream.

    Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

  • *2: When the ECM is replaced with a new one, reset memory is unnecessary.

PROCEDURE

1. REMOVE OIL PAN SUB-ASSEMBLY

Click here 2018 MY Camry [06/2017 - 08/2018]; 2GR-FKS (ENGINE MECHANICAL): CYLINDER HEAD GASKET: REMOVAL

2. REMOVE TIMING CHAIN CASE OIL SEAL

Click here 2018 MY Camry [06/2017 - 08/2018]; 2GR-FKS (ENGINE MECHANICAL): FRONT CRANKSHAFT OIL SEAL: REMOVAL+

3. REMOVE TIMING CHAIN COVER ASSEMBLY

(a) w/ Stud Bolt:

(1) Remove the 23 bolts and 2 nuts shown in the illustration.

*a

Nut

(b) w/o Stud Bolt:

(1) Remove the 25 bolts shown in the illustration.

(c) Remove the timing chain cover assembly by prying between the timing chain cover assembly and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver with its tip wrapped with protective tape.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly, cylinder block sub-assembly and timing chain cover assembly.

*a

Protective Tape

(d) Remove the oil pump gasket from the cylinder block sub-assembly.