| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000014Z1O |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [06/2017 - 09/2019] |
| Title: NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: Speaker Circuit; 2018 - 2019 MY Camry [06/2017 - 09/2019] | ||
|
Speaker Circuit |
DESCRIPTION
If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
Thus sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, DCM (telematics transceiver)* or speakers.
- *: w/ Manual (SOS) Switch
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click here
![2018 - 2020 MY Camry [06/2017 - 10/2020]; NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
-
Before replacing the DCM (telematics transceiver), refer to Registration.
Click here
PROCEDURE
|
1. |
CHECK SPEAKER (OPERATION CHECK) |
|
(a) Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check. Click here
|
|
(b) Perform the operation check above and determine the speaker that is not operating.
|
Not Operating Speaker |
Proceed to |
|---|---|
|
Front No. 1 speaker assembly or front No. 3 speaker assembly |
A |
|
Front No. 2 speaker assembly (w/ Manual (SOS) Switch) |
B |
|
Front No. 2 speaker assembly (w/o Manual (SOS) Switch) |
C |
|
Rear speaker assembly |
D |
|
Rear stereo component speaker assembly |
E |
HINT:
If sound cannot be heard from any speaker, inspect all of them.
| B |
|
| C |
|
| D |
|
| E |
|
|
|
2. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY - FRONT NO. 3 SPEAKER ASSEMBLY) |
(a) Disconnect the K14 stereo component amplifier assembly connector.
(b) Disconnect the N1 and O1 front No. 1 speaker assembly connectors.
(c) Disconnect the K109 and K110 front No. 3 speaker assembly connectors.
(d) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K14-15 (FR+) - K109-4 (+TW) |
Always |
Below 1 Ω |
|
K14-30 (FR-) - K109-2 (-TW) |
Always |
Below 1 Ω |
|
K14-13 (FL+) - K110-4 (+TW) |
Always |
Below 1 Ω |
|
K14-28 (FL-) - K110-2 (-TW) |
Always |
Below 1 Ω |
|
N1-2 - K109-3 (+) |
Always |
Below 1 Ω |
|
N1-1 - K109-1 (-) |
Always |
Below 1 Ω |
|
O1-2 - K110-3 (+) |
Always |
Below 1 Ω |
|
O1-1 - K110-1 (-) |
Always |
Below 1 Ω |
|
K14-15 (FR+) or K109-4 (+TW) - Body ground |
Always |
10 kΩ or higher |
|
K14-30 (FR-) or K109-2 (-TW) - Body ground |
Always |
10 kΩ or higher |
|
K14-13 (FL+) or K110-4 (+TW) - Body ground |
Always |
10 kΩ or higher |
|
K14-28 (FL-) or K110-2 (-TW) - Body ground |
Always |
10 kΩ or higher |
|
N1-2 or K109-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
N1-1 or K109-1 (-) - Body ground |
Always |
10 kΩ or higher |
|
O1-2 or K110-3 (+) - Body ground |
Always |
10 kΩ or higher |
|
O1-1 or K110-1 (-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
3. |
INSPECT FRONT NO. 1 SPEAKER ASSEMBLY |
(a) Remove the front No. 1 speaker assembly.
Click here
(b) Inspect the front No. 1 speaker assembly.
Click here
| NG |
|
|
|
4. |
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY |
(a) Remove the front No. 3 speaker assembly.
Click here
(b) Inspect the front No. 3 speaker assembly.
Click here
OK:
Malfunction disappears.
| OK |
|
END |
| NG |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
|
5. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - DCM (TELEMATICS TRANSCEIVER) - FRONT NO. 2 SPEAKER ASSEMBLY) |
(a) Disconnect the K14 stereo component amplifier assembly connector.
(b) Disconnect the K94 and K95 front No. 2 speaker assembly connectors.
(c) Disconnect the K12 DCM (telematics transceiver) connector.
(d) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K14-14 (TWR+) - K12-2 (SPI+) |
Always |
Below 1 Ω |
|
K14-29 (TWR-) - K12-3 (SPI-) |
Always |
Below 1 Ω |
|
K12-5 (SPO+) - K94-2 (TWR+) |
Always |
Below 1 Ω |
|
K12-6 (SPO-) - K94-1 (TWR-) |
Always |
Below 1 Ω |
|
K14-12 (TWL+) - K95-2 (TWL+) |
Always |
Below 1 Ω |
|
K14-27 (TWL-) - K95-1 (TWL-) |
Always |
Below 1 Ω |
|
K14-14 (TWR+) or K12-2 (SPI+) - Body ground |
Always |
10 kΩ or higher |
|
K14-29 (TWR-) or K12-3 (SPI-) - Body ground |
Always |
10 kΩ or higher |
|
K14-12 (TWL+) or K95-2 (TWL+) - Body ground |
Always |
10 kΩ or higher |
|
K14-27 (TWL-) or K95-1 (TWL-) - Body ground |
Always |
10 kΩ or higher |
|
K12-5 (SPO+) or K94-2 (TWR+) - Body ground |
Always |
10 kΩ or higher |
|
K12-6 (SPO-) or K94-1 (TWR-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
6. |
INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
(a) Remove the front No. 2 speaker assembly.
Click here
(b) Inspect the front No. 2 speaker assembly.
Click here
| NG |
|
|
|
7. |
INSPECT DCM (TELEMATICS TRANSCEIVER) |
(a) Remove the DCM (telematics transceiver).
Click here
|
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
| NG |
|
|
8. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY) |
(a) Disconnect the K14 stereo component amplifier assembly connector.
(b) Disconnect the K94 and K95 front No. 2 speaker assembly connectors.
(c) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K14-14 (TWR+) - K94-2 (TWR+) |
Always |
Below 1 Ω |
|
K14-29 (TWR-) - K94-1 (TWR-) |
Always |
Below 1 Ω |
|
K14-12 (TWL+) - K95-2 (TWL+) |
Always |
Below 1 Ω |
|
K14-27 (TWL-) - K95-1 (TWL-) |
Always |
Below 1 Ω |
|
K14-14 (TWR+) or K94-2 (TWR+) - Body ground |
Always |
10 kΩ or higher |
|
K14-29 (TWR-) or K94-1 (TWR-) - Body ground |
Always |
10 kΩ or higher |
|
K14-12 (TWL+) or K95-2 (TWL+) - Body ground |
Always |
10 kΩ or higher |
|
K14-27 (TWL-) or K95-1 (TWL-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
9. |
INSPECT FRONT NO. 2 SPEAKER ASSEMBLY |
(a) Remove the front No. 2 speaker assembly.
Click here
(b) Inspect the front No. 2 speaker assembly.
Click here
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
| NG |
|
|
10. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR SPEAKER ASSEMBLY) |
(a) Disconnect the K14 stereo component amplifier assembly connector.
(b) Disconnect the P1 and Q1 rear speaker assembly connectors.
(c) Measure the resistance according to the value (s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K14-11 (RR+) - P1-1 |
Always |
Below 1 Ω |
|
K14-26 (RR-) - P1-2 |
Always |
Below 1 Ω |
|
K14-9 (RL+) - Q1-1 |
Always |
Below 1 Ω |
|
K14-24 (RL-) - Q1-2 |
Always |
Below 1 Ω |
|
K14-11 (RR+) or P1-1 - Body ground |
Always |
10 kΩ or higher |
|
K14-26 (RR-) or P1-2 - Body ground |
Always |
10 kΩ or higher |
|
K14-9 (RL+) or Q1-1 - Body ground |
Always |
10 kΩ or higher |
|
K14-24 (RL-) or Q1-2 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
11. |
INSPECT REAR SPEAKER ASSEMBLY |
(a) Remove the rear speaker assembly.
Click here
(b) Inspect the rear speaker assembly.
Click here
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
| NG |
|
|
12. |
CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - REAR STEREO COMPONENT SPEAKER ASSEMBLY) |
(a) Disconnect the K14 stereo component amplifier assembly connector.
(b) Disconnect the R1 rear stereo component speaker assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K14-10 (WF1+) - R1-4 (WF1+) |
Always |
Below 1 Ω |
|
K14-25 (WF1-) - R1-3 (WF1-) |
Always |
Below 1 Ω |
|
K14-8 (WF2+) - R1-2 (WF2+) |
Always |
Below 1 Ω |
|
K14-23 (WF2-) - R1-1 (WF2-) |
Always |
Below 1 Ω |
|
K14-10 (WF1+) or R1-4 (WF1+) - Body ground |
Always |
10 kΩ or higher |
|
K14-25 (WF1-) or R1-3 (WF1-) - Body ground |
Always |
10 kΩ or higher |
|
K14-8 (WF2+) or R1-2 (WF2+) - Body ground |
Always |
10 kΩ or higher |
|
K14-23 (WF2-) or R1-1 (WF2-) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
13. |
INSPECT REAR STEREO COMPONENT SPEAKER ASSEMBLY |
(a) Remove the rear stereo component speaker assembly.
Click here
(b) Inspect the rear stereo component speaker assembly.
Click here
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
| NG |
|
|
|