PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: C168D; Vehicle Information Unmatched; 2018 - 2020 MY Camry [06/2017

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM1000000014XZK
Model Year Start: 2018	Model: Camry	Prod Date Range: [06/2017 - 10/2020]
Title: PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: C168D; Vehicle Information Unmatched; 2018 - 2020 MY Camry [06/2017 - 10/2020]

DTC

C168D

Vehicle Information Unmatched

DESCRIPTION

This DTC is stored if the television camera controller judges as a result of its self check that the vehicle information received via CAN communication and the vehicle information stored in the television camera controller do not match.
This DTC is stored if the rear television camera assembly judges as a result of its self check that the vehicle information received via CAN communication and the vehicle information stored in the television camera controller do not match.

Television Camera Controller

DTC No.	Detection Item	DTC Detection Condition	Trouble Area	DTC Output from
C168D	Vehicle Information Unmatched	Vehicle information unmatched	Camera view adjustment (calibration) Steering angle setting Television camera controller	Television camera controller

Rear Television Camera Assembly

DTC No.	Detection Item	DTC Detection Condition	Trouble Area	DTC Output from
C168D	Vehicle Information Unmatched	Vehicle information unmatched	Back camera position setting Steering angle setting Rear television camera assembly	Rear television camera assembly

CAUTION / NOTICE / HINT

NOTICE:

When "!" is displayed on the radio and display receiver assembly after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point.
Click here
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the panoramic view monitor system may be needed.
Click here

PROCEDURE

1.	CHECK DTC OUTPUT

(a) Recheck for DTCs and check that no DTCs are output.

Chassis > Panoramic View Monitor > Trouble Codes

Chassis > Parking Assist Camera > Trouble Codes

Result	Proceed to
DTC C168D is output ("Parking Assist Camera")	A
DTC C168D is output ("Panoramic View Monitor")	B

GO TO STEP 4

2.	PERFORM SETTINGS (BACK CAMERA POSITION SETTING, STEERING ANGLE SETTING)

(a) Perform the following procedure depending on the memory conditions to register the vehicle information into the rear television camera assembly.

(1) Refer to rear television camera assembly optical axis adjustment (back camera position setting).

Click here

(2) Refer to steering angle setting.

Click here

3.	CHECK DTC OUTPUT

(a) Clear the DTCs.

Chassis > Parking Assist Camera > Clear DTCs

(b) Recheck for DTCs and check that no DTCs are output.

Chassis > Parking Assist Camera > Trouble Codes

HINT:

If DTC C168D is output, perform the procedure to register the vehicle information into the rear television camera assembly.
If DTC C168D is still output after performing the procedure to register the vehicle information into the rear television camera assembly 3 times, replace the rear television camera assembly.

Result	Proceed to
DTC C168D is output	A
DTC C168D is not output	B

REPLACE REAR TELEVISION CAMERA ASSEMBLY

END

4.	PERFORM SETTINGS (CAMERA VIEW ADJUSTMENT [CALIBRATION], STEERING ANGLE SETTING)

(a) Perform the following procedure depending on the memory conditions to register the vehicle information to the television camera controller.

(1) Refer to camera view adjustment (calibration).

Click here

(2) Refer to steering angle setting.

Click here

5.	CHECK FOR DTC

(a) Clear the DTCs.

Chassis > Panoramic View Monitor > Clear DTCs

(b) Check for DTCs.

Chassis > Panoramic View Monitor > Trouble Codes

OK:

DTC C168D is not output.

HINT:

If DTC C168D is output, perform the procedure to allow the television camera controller to store the vehicle information again.
If DTC C168D is still output after performing the procedure to make the television camera controller store the vehicle information 3 times, replace the television camera controller.

END (SETTINGS ARE DEFECTIVE)

6.	READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG).

(d) Enter the following menus: Chassis / Panoramic View Monitor / Data List.

(e) Read the Data List according to the display on the Techstream.

Chassis > Panoramic View Monitor > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Back Camera Availability Consistency	Status of ECU stored in rear television camera assembly	OK/NG	OK: Normal NG: Rear television camera assembly or television camera controller is abnormal	-
Side Camera LH Availability Consistency	Status of ECU stored in side television camera assembly LH	OK/NG	OK: Normal NG: Side television camera assembly LH or television camera controller is abnormal	-
Front Camera Availability Consistency	Status of ECU stored in front television camera assembly	OK/NG	OK: Normal NG: Front television camera assembly or television camera controller is abnormal	-
Side Camera RH Availability Consistency	Status of ECU stored side television camera assembly RH	OK/NG	OK: Normal NG: Side television camera assembly RH or television camera controller is abnormal	-

Chassis > Panoramic View Monitor > Data List

Tester Display
Back Camera Availability Consistency
Side Camera LH Availability Consistency
Front Camera Availability Consistency
Side Camera RH Availability Consistency

Result	Proceed to
"NG" is displayed for any of the following items: Back Camera Availability Consistency Side Camera LH Availability Consistency Front Camera Availability Consistency Side Camera RH Availability Consistency	A
"OK" is displayed for all items.	B

ADJUST PANORAMIC VIEW MONITOR SYSTEM DISPLAY SETTING

REPLACE TELEVISION CAMERA CONTROLLER