Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014XZE
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 - 10/2020]
Title: PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: DATA LIST / ACTIVE TEST; 2018 - 2020 MY Camry [06/2017 - 10/2020]

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Start the engine.

(c) Turn the Techstream on.

(d) Enter the following menus: Chassis / Panoramic View Monitor / Data List.

(e) Read the Data List according to the display on the Techstream.

Chassis > Panoramic View Monitor > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

RHD/LHD Data Check

Status of the RHD/LHD data check

Normal/Abnormal

Normal: Television camera controller is normal

Abnormal: Television camera controller is abnormal

-

HV/ENG Data Check

Status of the HV/ENG data check

Normal/Abnormal

Normal: Television camera controller is normal

Abnormal: Television camera controller is abnormal

-

2WD/4WD Data Check

Status of the 2WD/AWD data check

Normal/Abnormal

Normal: Television camera controller ECU is normal

Abnormal: Television camera controller is abnormal

-

Main CPU Forced Termination Detection Record

A history item indicating that the main CPU did not enter standby status within 15 seconds of turning the engine switch off and a forced end was applied

No/Yes

No: Television camera controller is normal

Yes: Television camera controller is abnormal

-

Main CPU Abnormal Response Record

A history item indicating that the main CPU became unresponsive in normal status

No/Yes

No: Television camera controller is normal

Yes: Television camera controller is abnormal

-

Main CPU Abnormal Reset Record

A history item indicating that the main CPU was reset, although the engine switch was not turned off in normal status

No/Yes

No: Television camera controller is normal

Yes: Television camera controller is abnormal

-

Image Processing IC Written Protect Record

A history item indicating that the image processing IC memory was write protected

No/Yes

No: Television camera controller is normal

Yes: Television camera controller is abnormal

-

Image Processing IC Initialized Malfunction Record

A history item indicating that the image processing IC memory was not initialized

No/Yes

No: Television camera controller is normal

Yes: Television camera controller is abnormal

-

Main EEPROM Access Status

Main EEPROM access status

Normal/Abnormal

Normal: Television camera controller is normal

Abnormal: Television camera controller is abnormal

-

Sub EEPROM Access Status

Sub-EEPROM access status

Normal/Abnormal

Normal: Television camera controller is normal

Abnormal: Television camera controller is abnormal

-

System Power Supply Voltage Malfunction Record

A history item indicating an abnormally generated-voltage value from the system power source

No/Yes

No: Television camera controller is normal

Yes: Television camera controller is abnormal

-

Main CPU Starting Malfunction Record

A history item indicating that the main CPU did not start

No/Yes

No: Television camera controller is normal

Yes: Television camera controller is abnormal

-

CAN CPU Boot Malfunction Record

A history item indicating that the CPU controlling the input and output of the information obtained via CAN communication did not start and the information could not be retrieved

No/Yes

No: Television camera controller is normal

Yes: Television camera controller is abnormal

-

Wheel Speed Sensor (4wheel)

Reception state of the vehicle speed signal from the skid control ECU

Valid/Invalid

Valid: Speed signal received

Invalid: Speed signal not received

-

Bus-off Continuation Detection Record

A history item indicating that the bus off condition was detected

No/Yes

No: Television camera controller is normal

Yes: Television camera controller is abnormal

-

Shift R Position

Reverse signal

ON/OFF

OFF: Shift lever in any position except R

ON: Shift lever in R

-

Camera Changing SW Signal Status

Signal status at the BLSW terminal (switch camera signal)

ON/OFF

ON: Panoramic view monitor switch on

OFF: Panoramic view monitor switch off

-

Back Camera Availability Consistency

Status of ECU stored in rear television camera assembly

OK/NG

OK: Normal

NG: Rear television camera assembly or television camera controller is abnormal

-

Side Camera LH Availability Consistency

Status of ECU stored in side television camera assembly LH

OK/NG

OK: Normal

NG: Side television camera assembly LH or television camera controller is abnormal

-

Front Camera Availability Consistency

Status of ECU stored in front television camera assembly

OK/NG

OK: Normal

NG: Front television camera assembly or television camera controller is abnormal

-

Side Camera RH Availability Consistency

Status of ECU stored side television camera assembly RH

OK/NG

OK: Normal

NG: Side television camera assembly RH or television camera controller is abnormal

-

Image Adjustment Status

Status of the image adjustment status

Incomplete/Processing/Complete

Incomplete: Image adjustment incomplete

Processing: Image adjustment in processing

Complete: Image adjustment completed

-

Number of DTC

Number of DTCs (past and present)

Min: 0, Max: 255

Changes according to the number of DTCs output

-

Chassis > Parking Assist Camera > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Video Output Status

Output condition of video signal

OK or NG

OK: Output condition of video signal is normal

NG: Output condition of video signal is abnormal

-

Circumference Monitoring System Type Check

Verification of rear television camera assembly signal

OK or NG

OK: Rear television camera assembly normal

NG: Rear television camera assembly abnormal

-

EEPROM Status (Initial read)

Rear television camera assembly information

OK or NG

OK: Rear television camera assembly normal

NG: Rear television camera assembly abnormal

-

CPU Communication Status

Rear television camera assembly information

OK or NG

OK: Rear television camera assembly normal

NG: Rear television camera assembly abnormal

-

Number of DTC

Number of stored DTCs

min.: 0, max.: 255

Number of DTCs will be displayed

-

Current Key Cycle

Cumulative number of times the engine switch was turned on (IG)

Min.: 0, Max.: 65535 time

Cumulative number of times the engine switch was turned on (IG) will be displayed

-

Current Key Cycle Elapsed Time

Time elapsed since the engine switch was turned on (IG)

Min.: 0, Max.: 1677721.5 s

Time elapsed since the engine switch was turned on (IG) will be displayed

-