DOOR / HATCH: REAR DOOR: DISASSEMBLY; 2018 MY Camry [06/2017

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM1000000014WWZ
Model Year Start: 2018	Model: Camry	Prod Date Range: [06/2017 - 08/2018]
Title: DOOR / HATCH: REAR DOOR: DISASSEMBLY; 2018 MY Camry [06/2017 - 08/2018]

DISASSEMBLY

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane departure alert system (w/ Steering Control)
		Pre-collision system
		Intelligent clearance sonar system*
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system
Door window regulator sub-assembly Door glass Door glass run	Initialize Power Window Control System	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for A25A-FKS:

Click here

for 2GR-FKS:

Click here

3. REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY

(a) Using a moulding remover, disengage the 3 claws to remove the rear door armrest cover sub-assembly.

4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

(a) Disengage the 2 clips, 5 claws and 6 guides as shown in the illustration.

	Place Hand Here
	Remove in this Direction

(b) Disconnect the connector to remove the rear power window regulator switch assembly with rear door upper armrest base panel.

5. REMOVE REAR ARMREST ASSEMBLY

(a) Disengage the 3 clips, 8 claws and 2 guides as shown in the illustration.

Remove in this Direction

(b) Disengage the guide to remove the rear armrest assembly as shown in the illustration.

Remove in this Direction

6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

(a) Apply protective tape to the rear door panel as shown in the illustration.

Protective Tape

(b) Remove the 3 screws.

	Place Hand Here
	Remove in this Direction

(d) Pull out the rear door trim board sub-assembly as shown in the illustration to disengage the guide.

Remove in this Direction

(e) Raise the rear door trim board sub-assembly to separate the rear door trim board sub-assembly with the rear door inner glass weatherstrip and No. 1 door scuff plate clamp.

(f) Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly to remove the rear door trim board sub-assembly as shown in the illustration.

*1	Rear Door Inside Locking Cable Assembly
*2	Rear Door Lock Remote Control Cable Assembly
	Remove in this Direction

(g) Using a screwdriver, disengage the claw to remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly.

7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

(a) Slide the rear door inner glass weatherstrip to remove it from the rear door trim board sub-assembly as shown in the illustration.

Remove in this Direction

8. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER

(a) Disengage the clip.

(b) Remove the rear door No. 2 service hole cover.

9. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

(a) Disengage the 3 claws to remove the rear door inside handle sub-assembly.

10. REMOVE REAR SPEAKER ASSEMBLY

Click here

11. REMOVE REAR DOOR FRAME GARNISH

(a) Disengage the 2 claws to remove the rear door frame garnish.

12. REMOVE REAR DOOR SERVICE HOLE COVER

(a) Disconnect the connector.

(b) Disengage the 2 clamps.

13. REMOVE REAR DOOR NO. 1 VENT SEAL

(a) Remove the rear door No. 1 vent seal.

14. REMOVE REAR DOOR PANEL PROTECTOR

(a) Disengage the clip.

(b) Remove the rear door panel protector.

15. REMOVE REAR DOOR GLASS RUN

(a) Remove the rear door glass run.

16. REMOVE REAR DOOR CHECK ASSEMBLY

(a) Remove the 2 nuts, bolt and rear door check assembly.

	Nut
	Bolt

17. REMOVE REAR DOOR WEATHERSTRIP

(a) Using a clip remover, disengage the 23 clips and remove the rear door weatherstrip.

*a	Double-sided Tape

18. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

(a) Remove the screw, 2 bolts and rear door rear lower window frame sub-assembly.

	Screw
	Bolt

19. REMOVE REAR DOOR QUARTER WINDOW GLASS

(a) Remove the rear door quarter window glass with rear door quarter window weatherstrip as shown in the illustration.

Remove in this Direction

(b) Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

20. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

(a) Separate the rear door glass sub-assembly from the rear door window regulator assembly as shown in the illustration.

NOTICE:

After separating the rear door glass sub-assembly, do not allow it to fall.

(b) Remove the rear door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

NOTICE:

Do not damage the rear door glass sub-assembly.

	Remove in this Direction (1)
	Remove in this Direction (2)

21. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY

(a) Using a screwdriver, remove the rear door glass channel sub-assembly.

HINT:

Tape the screwdriver tip before use.

*a	Protective Tape

22. REMOVE REAR DOOR GLASS CHANNEL FILLER

(a) Remove the rear door glass channel filler from the rear door glass sub-assembly.

23. REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY

(a) Disconnect the connector.

(b) Loosen the temporary bolt.

NOTICE:

Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator assembly may fall and cause damage.

*a	Temporary Bolt

(d) Remove the temporary bolt from the rear door window regulator assembly.

24. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

Click here

25. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY

(a) Disengage the 2 claws and move the lever as shown in the illustration.

Disengage in this Direction

(b) Remove the rear door outside handle assembly as shown in the illustration.

Remove in this Direction

26. REMOVE REAR DOOR OUTSIDE HANDLE COVER

(a) Using a T30 "TORX" socket wrench, loosen the screw.

HINT:

The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.

(b) Disengage the claw to remove the rear door outside handle cover.

27. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD

(a) Disengage the 3 claws to remove the rear door front outside handle pad.

28. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD

(a) Disengage the claw and 3 guides to remove the rear door rear outside handle pad.

29. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

(a) Using a T30 "TORX" socket wrench, remove the screw.

*A	Inside
*B	Outside

(b) Slide the rear door outside handle frame sub-assembly as shown in the illustration to disengage the claw and then remove it.

30. REMOVE REAR DOOR PANEL CUSHION

(a) Disengage the 4 claws to remove the 2 rear door panel cushions.

31. REMOVE REAR DOOR NO. 2 WEATHERSTRIP

(a) Disengage the 5 clips to remove the rear door No. 2 weatherstrip.

32. REMOVE REAR DOOR BELT MOULDING ASSEMBLY

Click here

33. REMOVE DOOR WINDOW FRAME MOULDING CLIP

(a) Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws to remove the door window frame moulding clip.

*a	Protective Tape
	Remove in this Direction

34. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

Click here

35. REMOVE REAR DOOR FRONT OUTSIDE SEAL

(a) Disengage the guide to remove the rear door front outside seal.

36. REMOVE REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY

Click here

37. REMOVE REAR DOOR LOWER OUTSIDE STRIPE

Click here

38. REMOVE REAR DOOR OUTSIDE STRIPE

Click here