Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014WN6
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 - 10/2020]
Title: 2GR-FKS (BATTERY / CHARGING): GENERATOR: REMOVAL; 2018 - 2020 MY Camry [06/2017 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced generator assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

Front bumper assembly (w/ Panoramic view monitor system)

Front television camera view adjustment

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION for Initialization

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: CALIBRATION for Calibration

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry [03/2020 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 2018 MY Camry [06/2017 - 08/2018]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2019 MY Camry [08/2018 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2020 MY Camry [03/2020 - 10/2020]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

3. REMOVE RADIATOR ASSEMBLY

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; 2GR-FKS (COOLING): RADIATOR: REMOVAL

4. REMOVE V-BANK COVER SUB-ASSEMBLY

Click here 2018 MY Camry [06/2017 - 08/2018]; 2GR-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; 2GR-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

5. REMOVE V-RIBBED BELT

Click here 2018 - 2024 MY Camry [06/2017 -        ]; MAINTENANCE: 2GR-FKS DRIVE BELT: REMOVAL

6. REMOVE GENERATOR ASSEMBLY

(a) Open the terminal cap.

(b) Remove the nut and disconnect the wire harness from terminal B.

(c) Remove the 2 bolts.

(d) Disconnect the generator assembly connector.

(e) Disconnect the compressor assembly with magnetic clutch connector.

(f) Disconnect the camshaft timing oil control solenoid assembly connector.

(g) Disengage the 3 wire harness clamps and remove the wire harness clamp bracket.

(h) Remove the 2 bolts and generator assembly bracket.

(i) Remove the 2 bolts and generator assembly.