Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014WDD
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 - 10/2020]
Title: SLIDING ROOF / CONVERTIBLE: SLIDING ROOF HOUSING (for Panoramic Moon Roof): REMOVAL; 2018 - 2020 MY Camry [06/2017 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during sliding roof housing removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link
  • Sliding roof ECU (sliding roof drive gear)
  • Slide roof housing panel
  • Slide roof rail sub-assembly
  • Sliding roof glass sub-assembly

Initialize panoramic moon roof system (for Sliding Roof)
  • Auto operation function
  • Jam protection function
  • Key-off operation function
  • Key-linked function
  • Wireless transmitter linked function
  • Sliding roof open warning function

2018 - 2024 MY Camry [06/2017 -        ]; SLIDING ROOF / CONVERTIBLE: PANORAMIC MOON ROOF SYSTEM: INITIALIZATION

  • Roof sunshade ECU (sliding roof drive gear assembly)
  • Sunshade trim sub-assembly
  • Slide roof rail sub-assembly

Initialize panoramic moon roof system (for Roof Sunshade)
  • Auto operation function
  • Jam protection function
  • Key-off operation function

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane Departure Alert System (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision System

Intelligent clearance sonar system*

Memorize steering angle neutral point

Parking Assist Monitor System

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION 2020 MY Camry [09/2019 - 03/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION 2020 MY Camry [03/2020 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION

PROCEDURE

1. REMOVE SLIDING ROOF WEATHERSTRIP

(a) Move the sliding roof glass sub-assembly to the fully tilted up position.

(b) Remove the sliding roof weatherstrip.

Double-sided Tape

-

-

2. REMOVE NO. 3 SLIDING ROOF SIDE GARNISH LH

(a) Move the sunshade trim sub-assembly to the fully opened position.

(b) Remove the No. 3 sliding roof side garnish LH.

3. REMOVE NO. 3 SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.

4. REMOVE NO. 4 SLIDING ROOF SIDE GARNISH LH

(a) Remove the No. 4 sliding roof side garnish LH.

5. REMOVE NO. 4 SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.

6. REMOVE NO. 2 SLIDING ROOF SIDE GARNISH LH

(a) Move the sliding roof glass sub-assembly to the fully tilted up position.

(b) Remove the No. 2 sliding roof side garnish LH.

7. REMOVE NO. 2 SLIDING ROOF SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.

8. REMOVE SLIDING ROOF GLASS SUB-ASSEMBLY

(a) Move the sliding roof glass sub-assembly to the fully closed position.

(b) Using a T25 "TORX" socket wrench, remove the 6 screws and sliding roof glass sub-assembly.

NOTICE:

To prevent the sliding roof glass sub-assembly and sliding roof drive gear assembly from becoming misaligned, move the sliding roof glass sub-assembly to the fully closed position before removing.

9. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY LH

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: CURTAIN SHIELD AIRBAG ASSEMBLY: REMOVAL

10. REMOVE CURTAIN SHIELD AIRBAG ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

11. REMOVE ROOF ANTENNA ASSEMBLY (w/ Manual (SOS) Switch)

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; AUDIO / VIDEO: ROOF ANTENNA: REMOVAL+

12. DISCONNECT SLIDING ROOF DRAIN HOSE

HINT:

Use the same procedure for all of the sliding roof drain hoses.

(a) for Clamp Type:

(1) Disengage the claw and disconnect the sliding roof drain hose.

(b) for Clip Type:

(1) Expand the clip and disconnect the sliding roof drain hose.

13. REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET LH

(a) Remove the bolt, nut and front sliding roof housing mounting bracket LH.

Bolt

Nut

14. REMOVE FRONT SLIDING ROOF HOUSING MOUNTING BRACKET RH

HINT:

Use the same procedure as for the LH side.

15. REMOVE CENTER SLIDING ROOF HOUSING MOUNTING BRACKET LH

(a) Remove the 2 bolts, 2 nuts and center sliding roof housing mounting bracket LH.

Bolt

Nut

16. REMOVE CENTER SLIDING ROOF HOUSING MOUNTING BRACKET RH

HINT:

Use the same procedure as for the LH side.

17. REMOVE REAR SLIDING ROOF HOUSING MOUNTING BRACKET LH

(a) Remove the 2 bolts, 2 nuts and 2 rear sliding roof housing mounting brackets LH.

Bolt

Nut

18. REMOVE REAR SLIDING ROOF HOUSING MOUNTING BRACKET RH

HINT:

Use the same procedure as for the LH side.

19. REMOVE SLIDING ROOF HOUSING ASSEMBLY

(a) Remove the 20 nuts.

(b) Disengage the 2 guides and remove the sliding roof housing assembly.