| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000014WDB |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [06/2017 - ] |
| Title: SLIDING ROOF / CONVERTIBLE: SLIDING ROOF HOUSING (for Panoramic Moon Roof): DISASSEMBLY; 2018 - 2024 MY Camry [06/2017 - ] | ||
DISASSEMBLY
PROCEDURE
1. REMOVE NO. 1 SLIDING ROOF SIDE GARNISH LH
(a) Using a heat light, heat the No. 1 sliding roof side garnish LH.
Heating Temperature
|
Item |
Temperature |
|---|---|
|
No. 1 Sliding Roof Side Garnish LH |
20 to 30°C (68 to 86°F) |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
|
*a |
Heated Part |
|
*b |
Heat Light |
NOTICE:
Do not heat the No. 1 sliding roof side garnish LH excessively.
(b) Disengage the 28 claws and 2 guides to remove the No. 1 sliding roof side garnish LH.
|
Double-sided Tape |
- |
- |
2. REMOVE NO. 1 SLIDING ROOF SIDE GARNISH RH
HINT:
Use the same procedure as for the LH side.
3. REMOVE ROOF WIND DEFLECTOR PANEL SUB-ASSEMBLY
(a) Disengage the 3 claws.
|
*a |
Pin (A) |
*b |
Pin (B) |
|
*c |
Protective Tape |
- |
- |
(b) Disengage the 2 pins (A).
(c) Using a screwdriver with its tip wrapped with protective tape, disengage the 2 pins (B) to remove the roof wind deflector panel sub-assembly.
4. REMOVE NO. 2 ROOF WIRE
(a) Disconnect the 3 connectors.
(b) Disengage the 16 clamps to remove the No. 2 roof wire.
5. REMOVE SLIDING ROOF DRIVE GEAR ASSEMBLY (for Sliding Roof Glass)
|
(a) Remove the 2 bolts and sliding roof drive gear assembly. |
|
6. REMOVE SLIDING ROOF DRIVE GEAR ASSEMBLY (for Roof Sunshade)
|
(a) Remove the 2 bolts and sliding roof drive gear assembly. |
|
7. REMOVE REAR SLIDING ROOF GARNISH
(a) Using a heat light, heat the rear sliding roof garnish.
Heating Temperature
|
Item |
Temperature |
|---|---|
|
Rear Sliding Roof Garnish |
20 to 30°C (68 to 86°F) |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
|
*a |
Heated Part |
|
*b |
Heat Light |
NOTICE:
Do not heat the rear sliding roof garnish excessively.
(b) Disengage the 3 fasteners and 3 guides to remove the rear sliding roof garnish.
|
*a |
Fastener |
*b |
Guide |
|
*c |
Double-sided Tape |
- |
- |
8. REMOVE ROOM LIGHT BRACKET
|
(a) Remove the 2 nuts and room light bracket. |
|
9. REMOVE SLIDE ROOF RAIL SUB-ASSEMBLY
(a) Remove the 42 nuts and slide roof rail sub-assembly from the sliding roof housing panel.
10. REMOVE SUNSHADE TRIM SUB-ASSEMBLY
(a) Disengage the claw to remove the sliding roof sunshade guide RH as shown in the illustration.
|
Remove in this Direction |
HINT:
Use the same procedure for the RH side and LH side.
(b) Move the portion (A) as shown in the illustration to disengage the claw.
|
*a |
Portion A |
|
|
Remove in this Direction |
HINT:
Use the same procedure for the RH side and LH side.
(c) Slide the sliding roof sunshade runner and sunshade trim sub-assembly as shown in the illustration to separate them from the sliding roof guide rail sub-assembly RH.
|
*1 |
Sliding Roof Guide Rail Sub-assembly RH |
|
|
Remove in this Direction |
HINT:
Use the same procedure for the RH side and LH side.
(d) Remove the sunshade trim sub-assembly as shown in the illustration.
|
*A |
RH Side |
|
*a |
Retractor Cap |
|
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
NOTICE:
To prevent the sunshade trim sub-assembly from being damaged, fully push in the RH side retractor cap before lifting the sunshade trim sub-assembly to separate it from the slide roof rail sub-assembly.
HINT:
Separate the RH side first.
|
|