Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014WBH
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 -           ]
Title: 2GR-FKS (ENGINE MECHANICAL): ENGINE UNIT: INSTALLATION; 2018 - 2024 MY Camry [06/2017 -        ]

INSTALLATION

PROCEDURE

1. INSTALL ENGINE COVER BRACKET

(a) Install the engine cover bracket to the cylinder head cover sub-assembly LH with the bolt.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

2. INSTALL WATER FILLER BRACKET

(a) Temporarily install the water filler bracket to the camshaft housing sub-assembly LH with the 2 bolts.

*a

Stopper

*b

Protrusion

(b) Fully tighten the 2 bolts in the order shown in the illustration.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

NOTICE:

Make sure that the stopper of the water filler bracket is pressed against the protrusion of the camshaft housing sub-assembly LH when fully tightening the 2 bolts.

3. INSTALL WIRE HARNESS CLAMP BRACKET

(a) Install the wire harness clamp bracket to the camshaft housing sub-assembly with the bolt.

Torque:

30 N·m {306 kgf·cm, 22 ft·lbf}

(b) Install the wire harness clamp bracket to the camshaft housing sub-assembly LH with the bolt.

Torque:

30 N·m {306 kgf·cm, 22 ft·lbf}

4. INSTALL DRIVE SHAFT BEARING BRACKET

(a) Install the drive shaft bearing bracket to the cylinder block sub-assembly with the 3 bolts.

Torque:

63.7 N·m {650 kgf·cm, 47 ft·lbf}

NOTICE:

Make sure that there is no oil on the threads of the bolts.

5. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

(a) Install a new engine oil level dipstick guide O-ring to the engine oil level dipstick guide.

(b) Apply a light coat of engine oil to the engine oil level dipstick guide O-ring.

(c) Insert the engine oil level dipstick guide end into the oil pan sub-assembly.

(d) Install the engine oil level dipstick guide to the camshaft housing sub-assembly LH with the bolt.

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

(e) Install the engine oil level dipstick to the engine oil level dipstick guide.

6. INSTALL WATER PUMP PULLEY

Click here 2018 - 2024 MY Camry [06/2017 -        ]; 2GR-FKS (COOLING): WATER PUMP: INSTALLATION+

7. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

(a) Install the V-ribbed belt tensioner assembly with the 2 bolts.

Torque:

43 N·m {438 kgf·cm, 32 ft·lbf}

8. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

Click here 2018 - 2024 MY Camry [06/2017 -        ]; 2GR-FKS (COOLING): WATER PUMP: INSTALLATION+

9. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET

(a) Temporarily install the No. 1 compressor mounting bracket to the cylinder block sub-assembly with the 2 bolts.

(b) Fully tighten the 2 bolts in the order shown in the illustration.

Torque:

43 N·m {438 kgf·cm, 32 ft·lbf}

10. INSTALL COMPRESSOR ASSEMBLY WITH MAGNETIC CLUTCH

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; HEATING / AIR CONDITIONING: COMPRESSOR (for 2GR-FKS): INSTALLATION+ 2021 - 2024 MY Camry [10/2020 -        ]; HEATING / AIR CONDITIONING: COMPRESSOR (for 2GR-FKS): INSTALLATION+

11. INSTALL GENERATOR ASSEMBLY

Click here 2018 - 2024 MY Camry [06/2017 -        ]; 2GR-FKS (BATTERY / CHARGING): GENERATOR: INSTALLATION+

12. INSTALL V-RIBBED BELT

Click here 2018 - 2024 MY Camry [06/2017 -        ]; MAINTENANCE: 2GR-FKS DRIVE BELT: INSTALLATION+

13. INSTALL NO. 2 VENTILATION HOSE

(a) Install the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.

14. INSTALL VENTILATION HOSE

(a) Install the ventilation hose to the PCV valve (ventilation valve sub-assembly) and slide the clip to secure it.

15. INSTALL NO. 2 WATER BY-PASS HOSE

(a) Install the No. 2 water by-pass hose to the water outlet and slide the clip to secure it.

16. INSTALL NO. 3 WATER BY-PASS HOSE

(a) Install the No. 3 water by-pass hose to the water inlet pipe and slide the clip to secure it.

17. INSTALL VACUUM PUMP ASSEMBLY

Click here 2018 - 2024 MY Camry [06/2017 -        ]; BRAKE SYSTEM (OTHER): VACUUM PUMP (for 2GR-FKS): INSTALLATION+

18. INSTALL IGNITION COIL ASSEMBLY

Click here 2018 - 2024 MY Camry [06/2017 -        ]; 2GR-FKS (ENGINE CONTROL): IGNITION COIL AND SPARK PLUG: INSTALLATION+

19. INSTALL SENSOR WIRE

(a) Engage the 2 clamps and install the sensor wire with the bolt.

Torque:

10 N·m {102 kgf·cm, 7 ft·lbf}

20. INSTALL KNOCK CONTROL SENSOR

Click here 2018 - 2024 MY Camry [06/2017 -        ]; 2GR-FKS (ENGINE CONTROL): KNOCK SENSOR: INSTALLATION