- DTC judgment completed
- System normal
| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000014VFF |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [06/2017 - 08/2018] |
| Title: 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: P261029,P261093; ECM/PCM Engine Off Timer Performance Signal Invalid; 2018 MY Camry [06/2017 - 08/2018] | ||
|
DTC |
P261029 |
ECM/PCM Engine Off Timer Performance Signal Invalid |
|
DTC |
P261093 |
ECM/PCM Engine Off Timer Performance No Operation |
DTC SUMMARY
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
MIL |
Memory |
Note |
|---|---|---|---|---|---|---|
|
P261029 |
ECM/PCM Engine Off Timer Performance Signal Invalid |
ECM internal malfunction |
ECM |
Comes on |
DTC stored |
SAE Code: P2610 DTC for Mexico Models: Applies |
|
P261093 |
ECM/PCM Engine Off Timer Performance No Operation |
ECM internal malfunction |
ECM |
Comes on |
DTC stored |
SAE Code: P2610 DTC for Mexico Models: Does not apply |
|
DTC No. |
Monitoring Item |
Detection Timing |
Detection Logic |
|---|---|---|---|
|
P261029 |
Soak timer (built into ECM) |
EVAP monitoring (engine switch off) |
2 trip |
|
P261093 |
Soak timer (built into ECM) |
Engine switch on (IG) |
2 trip |
DESCRIPTION
The soak timer operates after the engine switch is turned off. When a certain amount of time has elapsed after turning the engine switch off, the soak timer activates the ECM to perform malfunction checks which can only be performed after the engine is stopped. The soak timer is built into the ECM.
MONITOR DESCRIPTION
If the soak timer activates the ECM even though only a short amount of time has elapsed since the engine switch was turned off, or if the soak timer does not activate the ECM even though a considerable amount of time has elapsed since the engine switch was turned off, the ECM determines that the soak timer is malfunctioning, illuminates the MIL and stores a DTC the next time the engine switch is turned on (IG).
MONITOR STRATEGY
|
Related DTC |
P2610: ECM internal engine off timer performance |
|
Required Sensors/Components (Main) |
ECM |
|
Required Sensors/Components (Related) |
- |
|
Frequency of Operation |
Once per driving cycle |
|
Duration |
2 times: Case 1 -: Case 2 and 3 |
|
MIL Operation |
2 driving cycles |
|
Sequence of Operation |
None |
TYPICAL ENABLING CONDITIONS
All
|
Monitor runs whenever the following DTCs are not stored |
None |
Case 1
|
All of the following conditions are met |
- |
|
Battery voltage |
8 V or higher |
|
Engine switch |
Off |
|
Internal Engine OFF Timer clear record |
Off |
Case 2
|
All of the following conditions are met |
- |
|
Internal engine off timer (elapsed time from engine stop) |
10 minutes or more, and less than 30 minutes |
|
Battery voltage |
8 V or higher |
|
Engine switch |
On (IG) |
|
Starter |
Off |
Case 3
|
All of the following conditions are met |
- |
|
Internal engine off timer (elapsed time from engine stop) |
40 minutes or more |
|
Battery voltage |
8 V or higher |
|
Engine switch |
On (IG) |
|
Starter |
Off |
TYPICAL MALFUNCTION THRESHOLDS
Case 1
|
One of the following conditions is met |
A, B or C |
|
A. Both of the following conditions are met |
- |
|
Internal engine off timer |
9.375 seconds or more |
|
CPU clock elapsed time |
1.96608 seconds or more, and less than 8.323072 seconds |
|
B. Both of the following conditions are met |
- |
|
Internal engine off timer |
18.75 seconds or more |
|
CPU clock elapsed time |
8.323072 to 10.42022 seconds |
|
C. Both of the following conditions are met |
- |
|
Internal engine off timer |
Less than 9.375 seconds |
|
CPU clock elapsed time |
More than 10.42022 seconds |
Case 2
|
ECM started by internal engine off timer last trip |
Yes |
Case 3
|
ECM started by internal engine off timer last trip |
No |
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
![2018 - 2024 MY Camry [06/2017 - ]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR](/t3Portal/stylegraphics/info.gif)
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
- Connect the Techstream to the DLC3.
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
- Turn the engine switch off and wait for at least 30 seconds.
- Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [A].
- Turn the engine switch off and wait for at least 15 seconds [B].
- Start the engine [C].
- Stop the engine and leave the vehicle for 60 minutes or more [D].
- Turn the engine switch on (IG).
- Turn the Techstream on.
- Enter the following menus: Powertrain / Engine / Trouble Codes [E].
-
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
- Enter the following menus: Powertrain / Engine / Utility / All Readiness.
- Input the DTC: P261029 or P261093.
-
Check the DTC judgment result.
Techstream Display
Description
NORMAL
ABNORMAL
- DTC judgment completed
- System abnormal
INCOMPLETE
- DTC judgment not completed
- Perform driving pattern after confirming DTC enabling conditions
HINT:
- If the judgment result is NORMAL, the system is normal.
- If the judgment result is ABNORMAL, the system has a malfunction.
-
[A] to [E]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
- When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.
CAUTION / NOTICE / HINT
HINT:
- DTC P261029 or P261093 is set if an internal ECM problem is detected. Diagnostic procedures are not required. ECM replacement is required.
- Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
|
1. |
REPLACE ECM |
(a) Replace the ECM.
Click here
|
|
2. |
CLEAR DTC |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Clear the DTC.
Powertrain > Engine > Clear DTCs
(e) Turn the engine switch off and wait for at least 30 seconds.
|
|
3. |
CHECK WHETHER DTC OUTPUT RECURS (DTC P261029 OR P261093) |
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Powertrain > Engine > Trouble Codes
(c) If no pending DTC is output, the repair has been successfully completed.
| NEXT |
|
END |
|
|