2GR-FKS (ENGINE CONTROL): SFI SYSTEM: P035113-P035613; Ignition Coil "A" Circuit Open; 2018 MY Camry [06/2017

HINT:

These DTCs indicate malfunctions relating to the primary circuit.
If DTC P035113 is output, check the No. 1 ignition coil assembly circuit.
If DTC P035213 is output, check the No. 2 ignition coil assembly circuit.
If DTC P035313 is output, check the No. 3 ignition coil assembly circuit.
If DTC P035413 is output, check the No. 4 ignition coil assembly circuit.
If DTC P035513 is output, check the No. 5 ignition coil assembly circuit.
If DTC P035613 is output, check the No. 6 ignition coil assembly circuit.

The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and one spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The spark of the spark plugs passes from the center electrode to the ground electrodes.

The ECM determines the ignition timing and transmits the ignition (IGT) signals to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches the current supplied to the primary coil on and off. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation (IGF) signal to the ECM for each cylinder ignition.

Reference: Inspection using an oscilloscope.

HINT:

The correct waveform is as shown.

While idling the engine, check the waveform between terminals IGT (1 to 6) and E1, and IGF (1 or 2) and E1 of the ECM connector.

ECM Terminal Name

CH1: Between IGT (1 to 6) and E1

CH2: Between IGF (1 or 2) and E1

Tester Range

2 V/DIV., 20 ms./DIV.

Condition

Idling with warm engine

MONITOR DESCRIPTION

If the ECM does not receive any IGF signals despite transmitting the IGT signal, it interprets this as a fault in the igniter and stores a DTC.

MONITOR STRATEGY

TYPICAL ENABLING CONDITIONS

TYPICAL MALFUNCTION THRESHOLDS

CONFIRMATION DRIVING PATTERN

HINT:

After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here

Connect the Techstream to the DLC3.
Turn the engine switch on (IG).
Turn the Techstream on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the engine switch off and wait for at least 30 seconds.
Start the engine [A].
Turn the Techstream on.
Idle the engine for 10 seconds or more [B].
Enter the following menus: Powertrain / Engine / Trouble Codes [C].
Read the pending DTCs.
HINT:
- If a pending DTC is output, the system is malfunctioning.
- If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P035113, P035213, P035313, P035413, P035513 or P035613.

Check the DTC judgment result.

Techstream Display	Description
NORMAL	DTC judgment completed System normal
ABNORMAL	DTC judgment completed System abnormal
INCOMPLETE	DTC judgment not completed Perform driving pattern after confirming DTC enabling conditions

HINT:

If the judgment result is NORMAL, the system is normal.
If the judgment result is ABNORMAL, the system is malfunctioning.
If the judgment result is INCOMPLETE, perform steps [B] through [C] again.
[A] to [C]: Normal judgment procedure.
The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.
When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

Inspect the fuses for circuits related to this system before performing the following procedure.

Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

Powertrain > Engine > Clear DTCs

(a) Shuffle the arrangement of the ignition coil assemblies (among No. 1 to No. 6 cylinders).

(b) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

Powertrain > Engine > Trouble Codes

(a) Remove the IG2 NO. 1 relay from the engine room relay block and junction block assembly.