Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014VCX
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 -           ]
Title: 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: CHECKING MONITOR STATUS; 2018 - 2024 MY Camry [06/2017 -        ]

CHECKING MONITOR STATUS

The purpose of the monitor result (mode 06) is to allow access to the results of on-board diagnostic monitoring tests of specific components/systems that are not continuously monitored. Examples are catalysts and evaporative emissions (EVAP) systems.

The monitor result allows the OBD II scan tool to display the monitor status, test value, minimum test limit and maximum test limit. These data are displayed after the vehicle has been driven to run the monitor.

When the test value is not between the minimum and maximum test limits, the ECM (PCM) interprets this as a malfunction. If the test value is on the borderline of the test limits, the component is likely to malfunction in the near future.

Perform the following procedures to view the monitor status. Although these procedures refer to the Lexus/Toyota Techstream, the monitor status can be checked using a generic OBD II scan tool. Refer to your scan tool operator's manual for specific procedural information.

PERFORM MONITOR DRIVE PATTERN

(a) Connect the Techstream to the DLC3.

(b) Turn the engine switch on (IG) and turn the Techstream on.

(c) Clear the DTCs.

Click here 2018 - 2024 MY Camry [06/2017 -        ]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs

(d) Operate the vehicle in accordance with the applicable drive pattern described in Readiness Monitor Drive Pattern. Do not turn the engine switch off.

Click here 2018 MY Camry [06/2017 - 08/2018]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: READINESS MONITOR DRIVE PATTERN 2019 - 2024 MY Camry [08/2018 -        ]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: READINESS MONITOR DRIVE PATTERN

NOTICE:

The test results will be lost if the engine switch is turned off.

ACCESS MONITOR RESULT

(a) Enter the following menus: Powertrain / Engine / Monitor / Current Monitor / Result.

Powertrain > Engine > Monitor

(b) Confirm the monitor status for each component.

HINT:

The monitor status for each component is displayed in the Result column.

  • Pass: The component is functioning normally.
  • Fail: The component is malfunctioning.

(c) Display the test results and test values for a monitor by selecting the icon in the Details column for that monitor.

CHECK COMPONENT STATUS

(a) Compare the Test Value with the minimum test limit (Min Limit) and maximum test limit (Max Limit).

(b) If the Test Value is between the minimum and maximum test limits, the component is functioning normally. If not, the component is malfunctioning. The test value is usually not near the test limits. If the test value is on the borderline of the test limits, the component is likely to malfunction in the near future.

HINT:

The monitor result might on rare occasions be Pass even if the Malfunction Indicator Lamp (MIL) is illuminated. This indicates the system malfunctioned on a previous driving cycle. This might be caused by an intermittent problem.

MONITOR RESULT INFORMATION

When using a generic scan tool, multiply the test value by the scaling value.

Refer to "Monitor Result" in each DTC related to the monitor.

Click here 2018 MY Camry [06/2017 - 08/2018]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: DIAGNOSTIC TROUBLE CODE CHART 2019 MY Camry [08/2018 - 09/2019]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: DIAGNOSTIC TROUBLE CODE CHART 2020 MY Camry [09/2019 - 10/2020]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: DIAGNOSTIC TROUBLE CODE CHART 2021 - 2024 MY Camry [10/2020 -        ]; 2GR-FKS (ENGINE CONTROL): SFI SYSTEM: DIAGNOSTIC TROUBLE CODE CHART