| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000014V96 |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [06/2017 - 10/2020] |
| Title: CRUISE CONTROL: LANE DEPARTURE ALERT SYSTEM (w/ Steering Control): DATA LIST / ACTIVE TEST; 2018 - 2020 MY Camry [06/2017 - 10/2020] | ||
DATA LIST / ACTIVE TEST
DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / LKA/LDA / Data List.
(e) Read the Data List according to the display on the Techstream.
Chassis > LKA/LDA > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Load System |
Whether the vehicle is equipped with LKA |
LDA or LKA |
LDA: Vehicle not equipped with LKA LKA: Vehicle equipped with LKA |
- |
|
LDA Control |
Lane departure alert system control status |
Prohibit or Permit |
Prohibit: Control prohibited Permit: Control permitted |
- |
|
Turn Signal Switch (Right) |
Turn signal switch (right) status |
OFF or ON |
ON: Turn signal light switch on (right) OFF: Turn signal light switch off |
- |
|
Turn Signal Switch (Left) |
Turn signal switch (left) status |
OFF or ON |
ON: Turn signal light switch on (left) OFF: Turn signal light switch off |
- |
|
Skid Control Buzzer Demand |
Lane departure alert buzzer demand status |
OFF or ON |
OFF: Lane departure alert buzzer not operating ON: Lane departure alert buzzer operating |
- |
|
Vehicle Information (2WD/4WD) |
- |
- |
- |
Not applicable to this vehicle. |
|
Vehicle Information (Conv/HV) |
- |
- |
- |
Not applicable to this vehicle. |
|
The Number of DTCs |
Number of stored DTCs |
0 to 255 |
Number of stored DTCs |
- |
ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / LKA/LDA / Active Test.
(e) Perform Active Test according to the display on the Techstream.
HINT:
The ignition switch must be turned to ON to proceed with the Active Test using the Techstream.
Chassis > LKA/LDA > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
LDA Buzzer |
Sounds the lane departure alert buzzer |
ON/OFF |
Confirm that the vehicle is stopped with the ignition switch ON. |
(f) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(g) Perform Active Test according to the display on the Techstream.
HINT:
The ignition switch must be turned to ON to proceed with the Active Test using the Techstream.
Body Electrical > Combination Meter > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Multi Display All (White) |
Multi-information display (White display) |
ON |
- |
|
|