Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014V96
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 - 10/2020]
Title: CRUISE CONTROL: LANE DEPARTURE ALERT SYSTEM (w/ Steering Control): DATA LIST / ACTIVE TEST; 2018 - 2020 MY Camry [06/2017 - 10/2020]

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Chassis / LKA/LDA / Data List.

(e) Read the Data List according to the display on the Techstream.

Chassis > LKA/LDA > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Load System

Whether the vehicle is equipped with LKA

LDA or LKA

LDA: Vehicle not equipped with LKA

LKA: Vehicle equipped with LKA

-

LDA Control

Lane departure alert system control status

Prohibit or Permit

Prohibit: Control prohibited

Permit: Control permitted

-

Turn Signal Switch (Right)

Turn signal switch (right) status

OFF or ON

ON: Turn signal light switch on (right)

OFF: Turn signal light switch off

-

Turn Signal Switch (Left)

Turn signal switch (left) status

OFF or ON

ON: Turn signal light switch on (left)

OFF: Turn signal light switch off

-

Skid Control Buzzer Demand

Lane departure alert buzzer demand status

OFF or ON

OFF: Lane departure alert buzzer not operating

ON: Lane departure alert buzzer operating

-

Vehicle Information (2WD/4WD)

-

-

-

Not applicable to this vehicle.

Vehicle Information (Conv/HV)

-

-

-

Not applicable to this vehicle.

The Number of DTCs

Number of stored DTCs

0 to 255

Number of stored DTCs

-

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Chassis / LKA/LDA / Active Test.

(e) Perform Active Test according to the display on the Techstream.

HINT:

The ignition switch must be turned to ON to proceed with the Active Test using the Techstream.

Chassis > LKA/LDA > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

LDA Buzzer

Sounds the lane departure alert buzzer

ON/OFF

Confirm that the vehicle is stopped with the ignition switch ON.

(f) Enter the following menus: Body Electrical / Combination Meter / Active Test.

(g) Perform Active Test according to the display on the Techstream.

HINT:

The ignition switch must be turned to ON to proceed with the Active Test using the Techstream.

Body Electrical > Combination Meter > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

Multi Display All (White)

Multi-information display (White display)

ON

-