EXTERIOR PANELS / TRIM: BLACK OUT TAPE (for Rear Door): REMOVAL; 2018 MY Camry [06/2017

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM1000000014UZM
Model Year Start: 2018	Model: Camry	Prod Date Range: [06/2017 - 08/2018]
Title: EXTERIOR PANELS / TRIM: BLACK OUT TAPE (for Rear Door): REMOVAL; 2018 MY Camry [06/2017 - 08/2018]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane departure alert system (w/ Steering Control)
		Pre-collision system
		Intelligent clearance sonar system*
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system
Rear door glass sub-assembly Rear door glass run	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for A25A-FKS:

Click here

for 2GR-FKS:

Click here

3. REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY

Click here

4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Click here

5. REMOVE REAR ARMREST ASSEMBLY

Click here

6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here

7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

Click here

8. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER

Click here

9. REMOVE REAR DOOR SERVICE HOLE COVER

Click here

10. REMOVE REAR DOOR NO. 1 VENT SEAL

Click here

11. REMOVE REAR DOOR PANEL PROTECTOR

Click here

12. REMOVE REAR DOOR GLASS RUN

Click here

13. DISCONNECT REAR DOOR WEATHERSTRIP

Click here

14. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

Click here

15. REMOVE REAR DOOR QUARTER WINDOW GLASS

Click here

16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Click here

17. REMOVE REAR DOOR FRAME GARNISH

Click here

18. REMOVE REAR DOOR LOWER OUTSIDE STRIPE

HINT:

When removing the rear door lower outside stripe, heat the vehicle body and rear door lower outside stripe using a heat light.

Heating Temperature

Item	Temperature
Rear Door Lower Outside Stripe and Vehicle Body	40 to 60°C (104 to 140°F)

CAUTION:

Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.

*a	Heated Part
*b	Heat Light

NOTICE:

Do not heat the vehicle body excessively.

(a) Using a heat light, heat the rear door lower outside stripe and vehicle body.

(b) Pull back on one of the ends of the rear door lower outside stripe to remove it.

HINT:

When pulling on the rear door lower outside stripe, pull it parallel to the vehicle body.

19. REMOVE REAR DOOR OUTSIDE STRIPE

HINT:

When removing the rear door outside stripe, heat the vehicle body and rear door outside stripe using a heat light.

Heating Temperature

Item	Temperature
Rear Door Outside Stripe and Vehicle Body	40 to 60°C (104 to 140°F)

CAUTION:

Do not touch the heat light and heated parts, touching the heat light may result in burns.
Touching heated parts for a long time may result in burns.

*a	Heated Part
*b	Heat Light

NOTICE:

Do not heat the vehicle body excessively.

(a) Using a heat light, heat the rear door outside stripe and vehicle body.

(b) Pull back on one of the ends of the rear door outside stripe to remove it.

HINT:

When pulling on the rear door outside stripe, pull it parallel to the vehicle body.