- Front door glass sub-assembly
- Front door glass run
| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000014UZL |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [06/2017 - 08/2018] |
| Title: EXTERIOR PANELS / TRIM: BLACK OUT TAPE (for Front Door): REMOVAL; 2018 MY Camry [06/2017 - 08/2018] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during black out tape removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
|
Pre-collision system |
|||
|
Intelligent clearance sonar system* |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system |
|
||
|
|
Initialize power window control system |
|
|
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
![2018 - 2019 MY Camry [06/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION](/t3Portal/stylegraphics/info.gif)
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
for A25A-FKS:
Click here
for 2GR-FKS:
Click here
3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH
Click here
4. REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY
Click here
5. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)
Click here
6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)
Click here
7. REMOVE FRONT ARMREST ASSEMBLY
Click here
8. REMOVE COURTESY LIGHT ASSEMBLY
Click here
9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Click here
10. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL
Click here
11. REMOVE FRONT DOOR SERVICE HOLE COVER
Click here
12. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
Click here
13. REMOVE FRONT DOOR PANEL PROTECTOR
Click here
14. REMOVE FRONT DOOR GLASS RUN
Click here
15. DISCONNECT FRONT DOOR WEATHERSTRIP
Click here
16. REMOVE DOOR FRAME GARNISH
Click here
17. REMOVE FRONT DOOR NO. 2 STRIPE
HINT:
When removing the front door No. 2 stripe, heat the vehicle body and front door No. 2 stripe using a heat light.
Heating Temperature
|
Item |
Temperature |
|---|---|
|
Front Door No. 2 Stripe and Vehicle Body |
40 to 60°C (104 to 140°F) |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
|
*a |
Heated Part |
|
*b |
Heat Light |
NOTICE:
Do not heat the vehicle body excessively.
(a) Using a heat light, heat the front door No. 2 stripe and vehicle body.
|
(b) Pull back on one of the ends of the front door No. 2 stripe to remove it. HINT: When pulling on the front door No. 2 stripe, pull it parallel to the vehicle body. |
|
18. REMOVE FRONT DOOR NO. 3 STRIPE
HINT:
When removing the front door No. 3 stripe, heat the vehicle body and front door No. 3 stripe using a heat light.
Heating Temperature
|
Item |
Temperature |
|---|---|
|
Front Door No. 3 Stripe and Vehicle Body |
40 to 60°C (104 to 140°F) |
CAUTION:
- Do not touch the heat light and heated parts, touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
|
*a |
Heated Part |
|
*b |
Heat Light |
NOTICE:
Do not heat the vehicle body excessively.
(a) Using a heat light, heat the front door No. 3 stripe and vehicle body.
|
(b) Pull back on one of the ends of the front door No. 3 stripe to remove it. HINT: When pulling on the front door No. 3 stripe, pull it parallel to the vehicle body. |
|
|
|