DOOR LOCK: REAR DOOR LOCK: REMOVAL; 2018 - 2020 MY Camry [06/2017

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM1000000014UYT
Model Year Start: 2018	Model: Camry	Prod Date Range: [06/2017 - 10/2020]
Title: DOOR LOCK: REAR DOOR LOCK: REMOVAL; 2018 - 2020 MY Camry [06/2017 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane departure alert system (w/ Steering Control)
		Pre-collision system
		Intelligent clearance sonar system*
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system
Rear door glass sub-assembly Rear door glass run	Initialize power window control system	Auto up and down function Jam protection function Remote control function Key-linked function Wireless transmitter-linked function Key-off operation function Catch protection function Window open warning function

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for A25A-FKS:

Click here

for 2GR-FKS:

Click here

3. REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY

Click here

4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Click here

5. REMOVE REAR ARMREST ASSEMBLY

Click here

6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here

7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

Click here

8. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER

Click here

9. REMOVE REAR DOOR SERVICE HOLE COVER

Click here

10. REMOVE REAR DOOR NO. 1 VENT SEAL

Click here

11. REMOVE REAR DOOR PANEL PROTECTOR

Click here

12. REMOVE REAR DOOR GLASS RUN

Click here

13. DISCONNECT REAR DOOR WEATHERSTRIP

(a) Disconnect the rear door weatherstrip until the screw of the rear door rear lower window frame sub-assembly is visible.

14. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

Click here

15. REMOVE REAR DOOR QUARTER WINDOW GLASS

Click here

16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Click here

17. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

(a) Using a T30 "TORX" socket wrench, remove the 3 screws.

*a	Release Plate
	Remove in this Direction

(b) Move the rear door lock with motor assembly downward to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.

(1) Remove the door lock wiring harness seal from the rear door lock with motor assembly.

18. REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY

(a) Using a screwdriver, disengage the 2 claws as shown in the illustration.

(b) Disengage the 2 claws to remove the rear door lock cover sub-assembly as shown in the illustration.

Remove in this Direction

19. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

(a) Remove the rear door lock remote control cable assembly as shown in the illustration.

Remove in this Direction

20. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

(a) Remove the rear door inside locking cable assembly as shown in the illustration.

Remove in this Direction