Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014UYT
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 - 10/2020]
Title: DOOR LOCK: REAR DOOR LOCK: REMOVAL; 2018 - 2020 MY Camry [06/2017 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear door lock with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

*: When performing learning using the Techstream.

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: INTELLIGENT CLEARANCE SONAR SYSTEM: CALIBRATION

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system*

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

  • Rear door glass sub-assembly
  • Rear door glass run

Initialize power window control system

  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Wireless transmitter-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

2018 - 2024 MY Camry [03/2017 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry [03/2020 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for A25A-FKS:

Click here 2018 MY Camry [06/2017 - 08/2018]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+

for 2GR-FKS:

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; MAINTENANCE: 2GR-FKS BATTERY: REMOVAL+

3. REMOVE REAR DOOR ARMREST COVER SUB-ASSEMBLY

Click here 2018 MY Camry [06/2017 - 08/2018]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR UPPER ARMREST BASE PANEL

Click here 2018 MY Camry [06/2017 - 08/2018]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

5. REMOVE REAR ARMREST ASSEMBLY

Click here 2018 MY Camry [06/2017 - 08/2018]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Click here 2018 MY Camry [06/2017 - 08/2018]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP

Click here 2018 MY Camry [06/2017 - 08/2018]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

8. REMOVE REAR DOOR NO. 2 SERVICE HOLE COVER

Click here 2018 MY Camry [06/2017 - 08/2018]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

9. REMOVE REAR DOOR SERVICE HOLE COVER

Click here 2018 MY Camry [06/2017 - 08/2018]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

10. REMOVE REAR DOOR NO. 1 VENT SEAL

Click here 2018 MY Camry [06/2017 - 08/2018]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

11. REMOVE REAR DOOR PANEL PROTECTOR

Click here 2018 MY Camry [06/2017 - 08/2018]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

12. REMOVE REAR DOOR GLASS RUN

Click here 2018 MY Camry [06/2017 - 08/2018]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

13. DISCONNECT REAR DOOR WEATHERSTRIP

(a) Disconnect the rear door weatherstrip until the screw of the rear door rear lower window frame sub-assembly is visible.

14. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY

Click here 2018 MY Camry [06/2017 - 08/2018]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

15. REMOVE REAR DOOR QUARTER WINDOW GLASS

Click here 2018 MY Camry [06/2017 - 08/2018]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

16. REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Click here 2018 MY Camry [06/2017 - 08/2018]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; DOOR / HATCH: REAR DOOR: DISASSEMBLY+

17. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY

(a) Using a T30 "TORX" socket wrench, remove the 3 screws.

*a

Release Plate

Remove in this Direction

(b) Move the rear door lock with motor assembly downward to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock with motor assembly.

(c) When reusing the rear door lock with motor assembly:

(1) Remove the door lock wiring harness seal from the rear door lock with motor assembly.

18. REMOVE REAR DOOR LOCK COVER SUB-ASSEMBLY

(a) Using a screwdriver, disengage the 2 claws as shown in the illustration.

(b) Disengage the 2 claws to remove the rear door lock cover sub-assembly as shown in the illustration.

Remove in this Direction

19. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY

(a) Remove the rear door lock remote control cable assembly as shown in the illustration.

Remove in this Direction

20. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY

(a) Remove the rear door inside locking cable assembly as shown in the illustration.

Remove in this Direction