SEAT: REAR SEAT ASSEMBLY (for Fixed Seat Type): REMOVAL; 2018 - 2020 MY Camry [06/2017

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM1000000014UUZ
Model Year Start: 2018	Model: Camry	Prod Date Range: [06/2017 - 10/2020]
Title: SEAT: REAR SEAT ASSEMBLY (for Fixed Seat Type): REMOVAL; 2018 - 2020 MY Camry [06/2017 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear seat assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative battery terminal	Perform steering sensor zero point calibration	Lane departure alert system (w/ Steering Control)
		Pre-collision system
		Intelligent clearance sonar system*
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.
Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.
Click here

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

for A25A-FKS:

Click here

for 2GR-FKS:

Click here

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
If an airbag deploys for any reason, it may cause a serious injury.

3. REMOVE REAR SEAT CUSHION ASSEMBLY

(a) Lift the front edge of the rear seat cushion assembly as shown in the illustration and disengage the 2 rear seat cushion frame hooks from the rear seat cushion lock hooks.

*a	Rear Seat Cushion Frame Hook
	Place Hand Here
	Remove in this Direction

NOTICE:

Be sure to hold the parts of the rear seat cushion assembly directly next to the rear seat cushion frame hooks when lifting it. Lifting a different part of the rear seat cushion assembly may deform the rear seat cushion frame.

HINT:

When lifting the rear seat cushion assembly, make sure to hold the area shown in the illustration.

Standard Measurement:

Area	Measurement
A	245 mm (9.64 in.)

(b) Loosen the bolt and separate the rear seat inner belt assembly RH and rear center seat outer belt assembly as a set from the anchor part of the floor panel.

(d) Pass the rear seat inner belt assembly RH and rear center seat outer belt assembly as shown in the illustration.

(e) Pass the rear seat inner belt assembly RH and rear center seat outer belt assembly through the rear seat cushion assembly as shown in the illustration.

(f) Remove the rear seat cushion assembly as shown in the illustration.

Remove in this Direction

4. REMOVE REAR SEAT CUSHION LOCK HOOK

(a) Disengage the 2 claws to remove the rear seat cushion lock hook as shown in the illustration.

Remove in this Direction

HINT:

Use the same procedure for the RH side and LH side.

5. REMOVE REAR SEATBACK ASSEMBLY

(a) Disconnect each rear seat outer belt from the rear seat shoulder belt guide RH, rear seat shoulder belt guide LH and rear seat center shoulder belt guide.

(b) Disconnect the 2 connectors.

(d) Disengage the 3 hooks to remove the rear seatback assembly as shown in the illustration.

Remove in this Direction