| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000014UQH |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [06/2017 - ] |
| Title: SLIDING ROOF / CONVERTIBLE: PANORAMIC MOON ROOF SYSTEM: B2342; Switch Failure; 2018 - 2024 MY Camry [06/2017 - ] | ||
|
DTC |
B2342 |
Switch Failure |
DESCRIPTION
This DTC is stored when the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) detects that the panoramic moon roof switch (roof console box sub-assembly) is stuck for 30 seconds or more.
Sliding Roof
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
B2342 |
Switch Failure |
Sliding roof ECU (sliding roof drive gear assembly) detects panoramic moon roof switch (roof console box sub-assembly) is stuck for 30 seconds or more. |
|
Sliding Sunshade
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
B2342 |
Switch Failure |
Roof sunshade ECU (sliding roof drive gear assembly) detects panoramic moon roof switch (roof console box sub-assembly) is stuck for 30 seconds or more. |
|
WIRING DIAGRAM
Refer to DTC B2341.
Click here
![2018 - 2024 MY Camry [06/2017 - ]; SLIDING ROOF / CONVERTIBLE: PANORAMIC MOON ROOF SYSTEM: B2341,B2344; Sensor (Motor) Failure+](/t3Portal/stylegraphics/info.gif)
CAUTION / NOTICE / HINT
NOTICE:
-
If the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear assembly) or roof sunshade ECU (sliding roof drive gear assembly) must be initialized.
Click here
-
The panoramic moon roof system uses the LIN communication system. First, confirm that there are no malfunctions in the LIN communication system. Refer to How to Proceed with Troubleshooting.
Click here
- DTC B2342 is stored in the sliding roof ECU (sliding roof drive gear assembly) and roof sunshade ECU (sliding roof drive gear assembly).
PROCEDURE
|
1. |
CHECK FOR DTC |
(a) Clear the DTCs.
Click here
Body Electrical > Sliding Roof > Clear DTCs
Body Electrical > Sliding Sunshade > Clear DTCs
(b) Check for DTCs.
Click here
Body Electrical > Sliding Roof > Trouble Codes
Body Electrical > Sliding Sunshade > Trouble Codes
OK:
DTC B2342 is not output.
| OK |
|
END (DUE TO SWITCH BEING OPERATED FOR 30 SECONDS OR MORE) |
|
|
2. |
CHECK DTC OUTPUT |
(a) Check the parts from which this DTC has been output.
|
Result |
Proceed to |
|---|---|
|
DTC output from sliding roof ECU (sliding roof drive gear assembly) |
A |
|
DTC output from roof sunshade ECU (sliding roof drive gear assembly) |
B |
| B |
|
|
|
3. |
READ VALUE USING TECHSTREAM (SLIDING ROOF) |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Sliding Roof / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Sliding Roof > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Current Roof Open Switch Stuck ON |
Sliding roof open switch stuck signal (Current) |
OFF or ON |
OFF: No sliding roof switch stuck signal (Current) ON: Sliding roof switch stuck signal (Current) |
- |
|
Current Roof Close Switch Stuck ON |
Sliding roof close switch stuck signal (Current) |
OFF or ON |
OFF: No sliding roof switch stuck signal (Current) ON: Sliding roof switch stuck signal (Current) |
- |
|
Current Shade Close Switch Stuck ON |
Roof sunshade close switch stuck signal (Current) |
OFF or ON |
OFF: No roof sunshade switch stuck signal (Current) ON: Roof sunshade switch stuck signal (Current) |
- |
|
Current Shade Open Switch Stuck ON |
Roof sunshade open switch stuck signal (Current) |
OFF or ON |
OFF: No roof sunshade switch stuck signal (Current) ON: Roof sunshade switch stuck signal (Current) |
- |
|
Past Roof Open Switch Stuck ON |
Sliding roof open switch stuck signal (Past) |
OFF or ON |
OFF: No sliding roof switch stuck signal (Past) ON: Sliding roof switch stuck signal (Past) |
- |
|
Past Roof Close Switch Stuck ON |
Sliding roof close switch stuck signal (Past) |
OFF or ON |
OFF: No sliding roof switch stuck signal (Past) ON: Sliding roof switch stuck signal (Past) |
- |
|
Past Shade Close Switch Stuck ON |
Roof sunshade close switch stuck signal (Past) |
OFF or ON |
OFF: No roof sunshade switch stuck signal (Past) ON: Roof sunshade switch stuck signal (Past) |
- |
|
Past Shade Open Switch Stuck ON |
Roof sunshade open switch stuck signal (Past) |
OFF or ON |
OFF: No roof sunshade switch stuck signal (Past) ON: Roof sunshade switch stuck signal (Past) |
- |
|
Current Vent Switch Stuck ON |
Tilt switch stuck signal (Current) |
OFF or ON |
OFF: No tilt switch stuck signal (Current) ON: Tilt switch stuck signal (Current) |
- |
|
Past Vent Switch Stuck ON |
Tilt switch stuck signal (Past) |
OFF or ON |
OFF: No tilt switch stuck signal (Past) ON: Tilt switch stuck signal (Past) |
- |
Body Electrical > Sliding Roof > Data List
|
Tester Display |
|---|
|
Current Roof Open Switch Stuck ON |
|
Current Roof Close Switch Stuck ON |
|
Current Shade Close Switch Stuck ON |
|
Current Shade Open Switch Stuck ON |
|
Past Roof Open Switch Stuck ON |
|
Past Roof Close Switch Stuck ON |
|
Past Shade Close Switch Stuck ON |
|
Past Shade Open Switch Stuck ON |
|
Current Vent Switch Stuck ON |
|
Past Vent Switch Stuck ON |
OK:
OFF appears on the Techstream screen.
| OK |
|
REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
|
|
|
4. |
CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)) |
(a) Disconnect the q1 sliding roof ECU (sliding roof drive gear assembly) connector.
(b) Disconnect the V14 panoramic moon roof switch (roof console box sub-assembly) connector.
(c) Disconnect the q2 roof sunshade ECU (sliding roof drive gear assembly) connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
q1-10 (ROOF OPEN) or V14-5 (OPN) - Body ground |
Always |
10 kΩ or higher |
|
q1-8 (ROOF CLOSE) or V14-4 (CLS) - Body ground |
Always |
10 kΩ or higher |
|
q1-4 (VENT) or V14-19 (B) - Body ground |
Always |
10 kΩ or higher |
|
q1-5 (SHADE OPEN) or V14-3 (UP) - Body ground |
Always |
10 kΩ or higher |
|
q1-9 (SHADE CLOSE) or V14-18 (DOWN) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
5. |
INSPECT PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY) |
(a) Remove the panoramic moon roof switch (roof console box sub-assembly).
Click here
(b) Inspect the panoramic moon roof switch (roof console box sub-assembly).
Click here
| OK |
|
REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
|
| NG |
|
REPLACE PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)
|
|
6. |
READ VALUE USING TECHSTREAM (SLIDING SUNSHADE) |
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Sliding Sunshade / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Sliding Sunshade > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Current Roof Open Switch Stuck ON |
Sliding roof open switch stuck signal (Current) |
OFF or ON |
OFF: No sliding roof switch stuck signal (Current) ON: Sliding roof switch stuck signal (Current) |
- |
|
Current Roof Close Switch Stuck ON |
Sliding roof close switch stuck signal (Current) |
OFF or ON |
OFF: No sliding roof switch stuck signal (Current) ON: Sliding roof switch stuck signal (Current) |
- |
|
Current Shade Close Switch Stuck ON |
Roof sunshade close switch stuck signal (Current) |
OFF or ON |
OFF: No roof sunshade switch stuck signal (Current) ON: Roof sunshade switch stuck signal (Current) |
- |
|
Current Shade Open Switch Stuck ON |
Roof sunshade open switch stuck signal (Current) |
OFF or ON |
OFF: No roof sunshade switch stuck signal (Current) ON: Roof sunshade switch stuck signal (Current) |
- |
|
Past Roof Open Switch Stuck ON |
Sliding roof open switch stuck signal (Past) |
OFF or ON |
OFF: No sliding roof switch stuck signal (Past) ON: Sliding roof switch stuck signal (Past) |
- |
|
Past Roof Close Switch Stuck ON |
Sliding roof close switch stuck signal (Past) |
OFF or ON |
OFF: No sliding roof switch stuck signal (Past) ON: Sliding roof switch stuck signal (Past) |
- |
|
Past Shade Close Switch Stuck ON |
Roof sunshade close switch stuck signal (Past) |
OFF or ON |
OFF: No roof sunshade switch stuck signal (Past) ON: Roof sunshade switch stuck signal (Past) |
- |
|
Past Shade Open Switch Stuck ON |
Roof sunshade open switch stuck signal (Past) |
OFF or ON |
OFF: No roof sunshade switch stuck signal (Past) ON: Roof sunshade switch stuck signal (Past) |
- |
|
Current Vent Switch Stuck ON |
Tilt switch stuck signal (Current) |
OFF or ON |
OFF: No tilt switch stuck signal (Current) ON: Tilt switch stuck signal (Current) |
- |
|
Past Vent Switch Stuck ON |
Tilt switch stuck signal (Past) |
OFF or ON |
OFF: No tilt switch stuck signal (Past) ON: Tilt switch stuck signal (Past) |
- |
Body Electrical > Sliding Sunshade > Data List
|
Tester Display |
|---|
|
Current Roof Open Switch Stuck ON |
|
Current Roof Close Switch Stuck ON |
|
Current Shade Close Switch Stuck ON |
|
Current Shade Open Switch Stuck ON |
|
Past Roof Open Switch Stuck ON |
|
Past Roof Close Switch Stuck ON |
|
Past Shade Close Switch Stuck ON |
|
Past Shade Open Switch Stuck ON |
|
Current Vent Switch Stuck ON |
|
Past Vent Switch Stuck ON |
OK:
OFF appears on the Techstream screen.
| OK |
|
REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
|
|
|
7. |
CHECK HARNESS AND CONNECTOR (ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY) - PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)) |
(a) Disconnect the q2 roof sunshade ECU (sliding roof drive gear assembly) connector.
(b) Disconnect the V14 panoramic moon roof switch (roof console box sub-assembly) connector.
(c) Disconnect the q1 sliding roof ECU (sliding roof drive gear assembly) connector.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
q2-10 (ROOF OPEN) or V14-5 (OPN) - Body ground |
Always |
10 kΩ or higher |
|
q2-8 (ROOF CLOSE) or V14-4 (CLS) - Body ground |
Always |
10 kΩ or higher |
|
q2-4 (VENT) or V14-19 (B) - Body ground |
Always |
10 kΩ or higher |
|
q2-5 (SHADE OPEN) or V14-3 (UP) - Body ground |
Always |
10 kΩ or higher |
|
q2-9 (SHADE CLOSE) or V14-18 (DOWN) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
8. |
INSPECT PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY) |
(a) Remove the panoramic moon roof switch (roof console box sub-assembly).
Click here
(b) Inspect the panoramic moon roof switch (roof console box sub-assembly).
Click here
| OK |
|
REPLACE ROOF SUNSHADE ECU (SLIDING ROOF DRIVE GEAR ASSEMBLY)
|
| NG |
|
REPLACE PANORAMIC MOON ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)
|
|
|