Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014TTY
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 -           ]
Title: A25A-FKS (ENGINE CONTROL): SFI SYSTEM: P06579E; Actuator Supply Voltage "A" Stuck On; 2018 - 2024 MY Camry [06/2017 -        ]

DTC

P06579E

Actuator Supply Voltage "A" Stuck On

MONITOR DESCRIPTION

The ECM monitors the output voltage to the throttle actuator. This self-check ensures that the ECM is functioning properly. The output voltage is usually 0 V when the ignition switch is turned off. If the output voltage is 7 V or higher when the ignition switch is turned off, the ECM will illuminate the MIL and store this DTC when the ignition switch is turned to ON.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P06579E

Actuator Supply Voltage "A" Stuck On

A throttle actuator power supply error (1 trip detection logic).

ECM

Comes on

DTC stored

  • SAE Code: P0657
  • DTC for Mexico Models: Applies

MONITOR STRATEGY

Related DTCs

P0657: Electronic throttle actuator supply voltage circuit performance

Required Sensors/Components (Main)

ECM

Required Sensors/Components (Related)

Throttle actuator

Frequency of Operation

Once per driving cycle

Duration

1 second

MIL Operation

Immediate

Sequence of Operation

None

TYPICAL ENABLING CONDITIONS

Monitor runs whenever the following DTCs are not stored

None

Both of the following conditions are met

-

Battery voltage

8 V or higher

Command to electronic throttle actuator power

Off

TYPICAL MALFUNCTION THRESHOLDS

Electronic throttle actuator power supply voltage

7 V or higher

CONFIRMATION DRIVING PATTERN

HINT:

  • After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.

    Click here 2018 - 2024 MY Camry [03/2017 -        ]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  • When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.

    Click here 2018 - 2024 MY Camry [03/2017 -        ]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM: DTC CHECK / CLEAR

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
  5. Turn the Techstream off.
  6. Turn the ignition switch off.
  7. Disconnect the Techstream.
  8. Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.
  9. Connect the cable to the negative (-) battery terminal.
  10. Turn the ignition switch to ON [A].
  11. Wait 10 seconds or more.
  12. Turn the ignition switch off [B].
  13. Wait 15 seconds or more.
  14. Connect the Techstream to the DLC3.
  15. Turn the ignition switch to ON.
  16. Turn the Techstream on.
  17. Wait 5 seconds or more [C].
  18. Enter the following menus: Powertrain / Engine / Trouble Codes [D].
  19. Read the pending DTCs.

    HINT:

    • If a pending DTC is output, the system is malfunctioning.
    • If a pending DTC is not output, perform the following procedure.
  20. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  21. Input the DTC: P06579E.
  22. Check the DTC judgment result.

    Techstream Display

    Description

    NORMAL

    • DTC judgment completed
    • System normal

    ABNORMAL

    • DTC judgment completed
    • System abnormal

    INCOMPLETE

    • DTC judgment not completed
    • Perform driving pattern after confirming DTC enabling conditions

    HINT:

    • If the judgment result is NORMAL, the system is normal.
    • If the judgment result is ABNORMAL, the system is malfunctioning.
    • If the judgment result is INCOMPLETE, perform steps [B] through [D] again.
    • [A] to [D]: Normal judgment procedure.

      The normal judgment procedure is used to complete DTC judgment and also used when clearing permanent DTCs.

    • When clearing the permanent DTCs, do not disconnect the cable from the battery terminal or attempt to clear the DTCs during this procedure, as doing so will clear the universal trip and normal judgment histories.

CAUTION / NOTICE / HINT

HINT:

Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CLEAR DTC

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Clear the DTCs.

Powertrain > Engine > Clear DTCs

(e) Turn the ignition switch off.

NEXT

2.

READ OUTPUT DTC (DTC P06579E)

(a) Disconnect the cable from the negative (-) battery terminal and wait for 1 minute.

(b) Connect the cable to the negative (-) battery terminal.

(c) Turn the ignition switch to ON.

(d) Wait 10 seconds or more.

(e) Turn the ignition switch off.

(f) Wait 15 seconds or more.

(g) Connect the Techstream to the DLC3.

(h) Turn the ignition switch to ON.

(i) Turn the Techstream on.

(j) Wait 5 seconds or more.

(k) Enter the following menus: Powertrain / Engine / Trouble Codes.

(l) Read the DTCs.

Powertrain > Engine > Trouble Codes

Result

Proceed to

DTCs are not output

A

DTC P06579E is output

B

A

CHECK FOR INTERMITTENT PROBLEMS

B

REPLACE ECM 2018 - 2020 MY Camry [06/2017 - 03/2020]; A25A-FKS (ENGINE CONTROL): ECM: REMOVAL 2020 MY Camry [03/2020 - 10/2020]; A25A-FKS (ENGINE CONTROL): ECM: REMOVAL 2021 - 2022 MY Camry [10/2020 - 08/2022]; A25A-FKS (ENGINE CONTROL): ECM: REMOVAL 2023 - 2024 MY Camry [08/2022 -        ]; A25A-FKS (ENGINE CONTROL): ECM: REMOVAL