Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM1000000014TSP |
Model Year Start: 2018 |
Model: Camry |
Prod Date Range: [06/2017 - 08/2018] |
Title: A25A-FKS (ENGINE CONTROL): SFI SYSTEM: P030000,P030027,P030085-P030400; Random/Multiple Cylinder Misfire Detected; 2018 MY Camry [06/2017 - 08/2018] |
DTC
|
P030000
|
Random/Multiple Cylinder Misfire Detected
|
DTC
|
P030027
|
Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold
|
DTC
|
P030085
|
Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range
|
DTC
|
P030100
|
Cylinder 1 Misfire Detected
|
DTC
|
P030200
|
Cylinder 2 Misfire Detected
|
DTC
|
P030300
|
Cylinder 3 Misfire Detected
|
DTC
|
P030400
|
Cylinder 4 Misfire Detected
|
DESCRIPTION
When the engine misfires, high concentrations of hydrocarbons (HC) enter the exhaust gas. Extremely high hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire count. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the camshaft position sensor and the crankshaft position sensor. The camshaft position sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, and could cause emission control system performance deterioration, the ECM illuminates the MIL and stores a DTC.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Memory
|
Note
|
P030000
|
Random/Multiple Cylinder Misfire Detected
|
Simultaneous misfiring of several cylinders occurs and one of the following conditions is met (2 trip detection logic):
-
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).
-
An emission deterioration misfire occurs (MIL illuminates).
|
-
Open or short in engine wire harness
-
Connector connection
-
Vacuum hose connections
-
Ignition system
-
Port fuel injector assembly
-
Direct fuel injector assembly
-
Fuel pressure
-
Mass air flow meter sub-assembly
-
Engine coolant temperature sensor
-
Compression pressure
-
Valve timing
-
PCV valve and hose
-
PCV hose connections
-
Intake system
-
EGR valve assembly
-
ECM
|
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
|
DTC stored
|
-
SAE Code: P0300
-
DTC for Mexico Models: Applies
|
P030027
|
Random/Multiple Cylinder Misfire Detected (Emission) Signal Rate of Change Above Threshold
|
An emission deterioration misfire occurs (2 trip detection logic).
|
-
Open or short in engine wire harness
-
Connector connection
-
Vacuum hose connections
-
Ignition system
-
Port fuel injector assembly
-
Direct fuel injector assembly
-
Fuel pressure
-
Mass air flow meter sub-assembly
-
Engine coolant temperature sensor
-
Compression pressure
-
Valve timing
-
PCV valve and hose
-
PCV hose connections
-
Intake system
-
EGR valve assembly
-
ECM
|
Comes on
|
DTC stored
|
-
SAE Code: -
-
DTC for Mexico Models: Applies
|
P030085
|
Random / Multiple Cylinder Misfire Detected (Over Temperature) Signal Above Allowable Range
|
A misfire occurs that may damage the three-way catalytic converter (2 trip detection logic).
|
-
Open or short in engine wire harness
-
Connector connection
-
Vacuum hose connections
-
Ignition system
-
Port fuel injector assembly
-
Direct fuel injector assembly
-
Fuel pressure
-
Mass air flow meter sub-assembly
-
Engine coolant temperature sensor
-
Compression pressure
-
Valve timing
-
PCV valve and hose
-
PCV hose connections
-
Intake system
-
EGR valve assembly
-
ECM
|
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
|
DTC stored
|
-
SAE Code: -
-
DTC for Mexico Models: Applies
|
P030100
|
Cylinder 1 Misfire Detected
|
Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
-
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).
-
An emission deterioration misfire occurs (MIL illuminates).
|
-
Open or short in engine wire harness
-
Connector connection
-
Vacuum hose connections
-
Ignition system
-
Port fuel injector assembly
-
Direct fuel injector assembly
-
Fuel pressure
-
Mass air flow meter sub-assembly
-
Engine coolant temperature sensor
-
Compression pressure
-
Valve timing
-
PCV valve and hose
-
PCV hose connections
-
Intake system
-
EGR valve assembly
-
ECM
|
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
|
DTC stored
|
-
SAE Code: P0301
-
DTC for Mexico Models: Applies
|
P030200
|
Cylinder 2 Misfire Detected
|
Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
-
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).
-
An emission deterioration misfire occurs (MIL illuminates).
|
-
Open or short in engine wire harness
-
Connector connection
-
Vacuum hose connections
-
Ignition system
-
Port fuel injector assembly
-
Direct fuel injector assembly
-
Fuel pressure
-
Mass air flow meter sub-assembly
-
Engine coolant temperature sensor
-
Compression pressure
-
Valve timing
-
PCV valve and hose
-
PCV hose connections
-
Intake system
-
EGR valve assembly
-
ECM
|
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
|
DTC stored
|
-
SAE Code: P0302
-
DTC for Mexico Models: Applies
|
P030300
|
Cylinder 3 Misfire Detected
|
Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
-
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).
-
An emission deterioration misfire occurs (MIL illuminates).
|
-
Open or short in engine wire harness
-
Connector connection
-
Vacuum hose connections
-
Ignition system
-
Port fuel injector assembly
-
Direct fuel injector assembly
-
Fuel pressure
-
Mass air flow meter sub-assembly
-
Engine coolant temperature sensor
-
Compression pressure
-
Valve timing
-
PCV valve and hose
-
PCV hose connections
-
Intake system
-
EGR valve assembly
-
ECM
|
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
|
DTC stored
|
-
SAE Code: P0303
-
DTC for Mexico Models: Applies
|
P030400
|
Cylinder 4 Misfire Detected
|
Misfiring of a specific cylinder occurs and one of the following conditions is met (2 trip detection logic):
-
A misfire occurs that may damage the three-way catalytic converter (MIL blinks immediately when detected).
-
An emission deterioration misfire occurs (MIL illuminates).
|
-
Open or short in engine wire harness
-
Connector connection
-
Vacuum hose connections
-
Ignition system
-
Port fuel injector assembly
-
Direct fuel injector assembly
-
Fuel pressure
-
Mass air flow meter sub-assembly
-
Engine coolant temperature sensor
-
Compression pressure
-
Valve timing
-
PCV valve and hose
-
PCV hose connections
-
Intake system
-
EGR valve assembly
-
ECM
|
Comes on/Blinks*
*: The MIL flashes when a catalyst-damaging misfire is detected.
|
DTC stored
|
-
SAE Code: P0304
-
DTC for Mexico Models: Applies
|
When DTCs for misfiring cylinders are randomly stored, but DTC P030000 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P030000 is only stored when several misfiring cylinders are detected at the same time.
MONITOR DESCRIPTION
The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
-
Within the first 1000 crankshaft revolutions after the engine starts, an excessive number of misfires (approximately 10 to 70 misfires per 1000 crankshaft revolutions) occurs once.
-
An excessive number of misfires (approximately 10 to 70 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.
-
At a high engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected once.
-
At a normal engine speed, a sufficient amount of misfires to damage the catalyst occurring within 200 crankshaft revolutions is detected 3 times.
Misfire Monitor for Mexico Models:
-
The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
-
Within the first 1000 crankshaft revolutions after the engine starts, an excessive number of misfires (approximately 1000 misfires per 1000 crankshaft revolutions) occurs once.
-
An excessive number of misfires (approximately 500 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediately detection logic) and stores a DTC (2 trip detection logic) when the following condition, which could cause the three-way catalytic converter damage, is detected (2 trip detection logic).
-
A catalyst-damaging misfire, which is monitored every 200 crankshaft revolutions, occurs 3 times.
MONITOR STRATEGY
Related DTCs
|
P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
|
Required Sensors/Components (Main)
|
Crankshaft position sensor
Camshaft position sensor
|
Required Sensors/Components (Related)
|
Engine coolant temperature
Intake air temperature sensor (mass air flow meter sub-assembly)
Mass air flow meter sub-assembly
|
Frequency of Operation
|
Continuous
|
Duration
|
1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emission-related misfire)
200 crankshaft revolutions (1 or 3 times) (Catalyst-damaging misfire)
|
MIL Operation
|
2 driving cycles: Emission-related misfire
MIL flashes immediate: Catalyst-damaging misfire
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
Misfire
Monitor runs whenever the following DTCs are not stored
|
P0016 (VVT system - misalignment)
P0017 (Exhaust VVT system - misalignment)
P0101, P0102, P0103 (Mass air flow meter)
P0107, P0108 (Manifold absolute pressure)
P0111, P0112, P0113 (Intake air temperature sensor)
P0117, P0118 (Engine coolant temperature sensor)
P0121, P0122, P0123, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0327, P0328 (Knock control sensor)
P0335, P0337, P0338 (Crankshaft position sensor)
P0340, P0342, P0343 (Camshaft position sensor)
P0365, P0367, P0368 (Exhaust camshaft position sensor)
P0500 (Vehicle speed sensor)
|
Battery voltage
|
8 V or higher
|
VVT system
|
Not operated by scan tool
|
Engine speed
|
400 to 6800 rpm
|
Either of the following conditions is met
|
(a) or (b)
|
(a) Engine coolant temperature at engine start
|
Higher than -7°C (19°F)
|
(b) Engine coolant temperature
|
Higher than 20°C (68°F)
|
Fuel cut
|
Off
|
Monitor Period of Emission-related Misfire
First 1000 revolutions after engine start, or during check mode
|
Crankshaft 1000 revolutions
|
Except above
|
Crankshaft 1000 revolutions x 4
|
Monitor Period of Catalyst-damaging Misfire (MIL Blinks)
All of the following conditions 1, 2, 3 and 4 are met
|
Crankshaft 200 revolutions x 3
|
Except above (MIL blinks immediately)
|
Crankshaft 200 revolutions
|
1. Driving cycles
|
1st
|
2. Check mode
|
Off
|
3. Engine speed
|
Less than 2300 rpm
|
4. Engine load
|
Less than 65%
|
Misfire for Mexico Models
Monitor runs whenever the following DTCs are not stored
|
P0016 (VVT system - misalignment)
P0017 (Exhaust VVT system - misalignment)
P0101, P0102, P0103 (Mass air flow meter)
P0107, P0108 (Manifold absolute pressure)
P0111, P0112, P0113 (Intake air temperature sensor)
P0117, P0118 (Engine coolant temperature sensor)
P0121, P0122, P0123, P0222, P0223, P2135 (Throttle position sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P0327, P0328 (Knock control sensor)
P0335, P0337, P0338 (Crankshaft position sensor)
P0340, P0342, P0343 (Camshaft position sensor)
P0365, P0367, P0368 (Exhaust camshaft position sensor)
P0500 (Vehicle speed sensor)
|
Battery voltage
|
8 V or higher
|
VVT system
|
Not operated by scan tool
|
Engine speed
|
400 to 6800 rpm
|
Engine coolant temperature
|
Higher than 65°C (149°F)
|
Fuel cut
|
Off
|
Monitor Period of Emission-related Misfire for Mexico Models
First 1000 revolutions after engine start, or during check mode
|
Crankshaft 1000 revolutions
|
Except above
|
Crankshaft 1000 revolutions x 4
|
Monitor Period of Catalyst-damaging Misfire (MIL Blinks) for Mexico Models
MIL blinks immediately
|
Crankshaft 200 revolutions x 3
|
TYPICAL MALFUNCTION THRESHOLDS
Monitor Period of Emission-related Misfire
Misfire rate
|
2.5625% or higher
|
Monitor Period of Catalyst-damaging Misfire (MIL Blinks)
Number of misfires per 200 revolutions
|
137 or more (varies with engine speed and engine load)
|
Monitor Period of Emission-related Misfire for Mexico Models
Misfire rate
|
2.5625% or higher
|
Monitor Period of Catalyst-damaging Misfire (MIL Blinks) for Mexico Models
Number of misfires per 200 revolutions
|
50% or higher: for 1st 1000 revolutions
25% or higher: after 1st 1000 revolutions
|
MONITOR RESULT
Refer to detailed information in Checking Monitor Status.
Click here
P0300: Misfire / EWMA MISFIRE
Monitor ID
|
Test ID
|
Scaling
|
Unit
|
Description
|
$A1
|
$0B
|
Multiply by 1
|
Count
|
Total EWMA* misfire count of all cylinders in last ten driving cycles
|
P0300: Misfire / MISFIRE RATE
Monitor ID
|
Test ID
|
Scaling
|
Unit
|
Description
|
$A1
|
$0C
|
Multiply by 1
|
Count
|
-
When ignition switch ON, total misfire count of all cylinders in last driving cycle is displayed.
-
While engine is running, total misfire count of all cylinders in current driving cycle is displayed.
|
P0301: Misfire / EWMA MISFIRE1
Monitor ID
|
Test ID
|
Scaling
|
Unit
|
Description
|
$A2
|
$0B
|
Multiply by 1
|
Count
|
Total EWMA* misfire count of cylinder 1 in last ten driving cycles
|
P0301: Misfire / MISFIRE RATE1
Monitor ID
|
Test ID
|
Scaling
|
Unit
|
Description
|
$A2
|
$0C
|
Multiply by 1
|
Count
|
-
When ignition switch ON, total misfire count of cylinder 1 in last driving cycle is displayed.
-
While engine is running, total misfire count of cylinder 1 in current driving cycle is displayed.
|
P0302: Misfire / EWMA MISFIRE2
Monitor ID
|
Test ID
|
Scaling
|
Unit
|
Description
|
$A3
|
$0B
|
Multiply by 1
|
Count
|
Total EWMA* misfire count of cylinder 2 in last ten driving cycles
|
P0302: Misfire / MISFIRE RATE2
Monitor ID
|
Test ID
|
Scaling
|
Unit
|
Description
|
$A3
|
$0C
|
Multiply by 1
|
Count
|
-
When ignition switch ON, total misfire count of cylinder 2 in last driving cycle is displayed.
-
While engine is running, total misfire count of cylinder 2 in current driving cycle is displayed.
|
P0303: Misfire / EWMA MISFIRE3
Monitor ID
|
Test ID
|
Scaling
|
Unit
|
Description
|
$A4
|
$0B
|
Multiply by 1
|
Count
|
Total EWMA* misfire count of cylinder 3 in last ten driving cycles
|
P0303: Misfire / MISFIRE RATE3
Monitor ID
|
Test ID
|
Scaling
|
Unit
|
Description
|
$A4
|
$0C
|
Multiply by 1
|
Count
|
-
When ignition switch ON, total misfire count of cylinder 3 in last driving cycle is displayed.
-
While engine is running, total misfire count of cylinder 3 in current driving cycle is displayed.
|
P0304: Misfire / EWMA MISFIRE4
Monitor ID
|
Test ID
|
Scaling
|
Unit
|
Description
|
$A5
|
$0B
|
Multiply by 1
|
Count
|
Total EWMA* misfire count of cylinder 4 in last ten driving cycles
|
P0304: Misfire / MISFIRE RATE4
Monitor ID
|
Test ID
|
Scaling
|
Unit
|
Description
|
$A5
|
$0C
|
Multiply by 1
|
Count
|
-
When ignition switch ON, total misfire count of cylinder 4 in last driving cycle is displayed.
-
While engine is running, total misfire count of cylinder 4 in current driving cycle is displayed.
|
HINT:
*: EWMA (Exponential Weighted Moving Average) misfire counts for last 10 driving cycles (calculated) Calculation: 0.1 x (current counts) + 0.9 x (previous average)
Initial value for (previous average) = 0
CONFIRMATION DRIVING PATTERN
HINT:
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
-
Permanent misfire and fuel system DTCs can only be cleared when performing the universal trip driving pattern when no malfunction is detected.
-
Connect the Techstream to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the Techstream on.
-
Record the DTC(s) and Freeze Frame Data.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Using the Techstream, switch the ECM from normal mode to check mode.
Click here
-
Start the engine.
-
Read the misfire counts of each cylinder, Misfire Count Cylinder #1 to Misfire Count Cylinder #4, with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
-
Drive the vehicle so that the vehicle conditions displayed in Misfire RPM and Misfire Load of the Data List are the same as the Freeze Frame Data. Perform this step several times.
HINT:
In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, confirm the Misfire RPM and Misfire Load in the Data List.
Engine speed
|
Duration
|
Idling
|
8.0 minutes or more
|
1000
|
4.5 minutes or more
|
2000
|
2.5 minutes or more
|
3000
|
1.5 minutes or more
|
-
Check whether misfires have occurred by checking DTCs and Freeze Frame Data.
HINT:
Do not turn the ignition switch off until the output DTC(s) and Freeze Frame Data have been recorded. When the ECM returns to normal mode (default), the stored DTC(s), Freeze Frame Data and other data are cleared.
-
Record the DTC(s), Freeze Frame Data and misfire counts.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the ignition switch off and wait for at least 30 seconds.
WIRING DIAGRAM
Refer to DTC P010012 for the mass air flow meter sub-assembly circuit.
Click here
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following procedure.
HINT:
-
Check the "Fuel Cut Elapsed Time" in the Data List or the Freeze Frame Data.
If the elapsed time is over 0 seconds, then the engine speed is high (engine speed at which fuel cut occurs + 500 rpm).
When this has happened, there is the possibility that the No. 1 valve rocker arm sub-assembly will become loose and a fire could start, so check that the No. 1 valve rocker arm sub-assembly is properly attached.
-
By clearing the DTCs, "Fuel Cut Elapsed Time" will be cleared.
-
In the past, when the primary ignition system (the igniter drive circuit in the ECM, the primary circuit in the ignition coil assembly, the related wire harness, or the connector) was out of order, diagnostic codes from P035113 to P035413 were output. However, these codes are not output in this vehicle.
When a failure in the primary ignition system is suspected, refer to "Catalyst OT Misfire Fuel Cut History", "Catalyst OT Misfire Fuel Cut Cylinder #1 to #4", and "Misfire Count Cylinder #1 to #4" in the Freeze Frame Data, the pending Freeze Frame Data, and the Data List, and confirm in which cylinder the high-frequency misfire was concentrated.
-
Referring to the following contents of the Freeze Frame Data (or the pending Freeze Frame Data) enables an estimation of which cylinder has misfired and to what degree.
-
Misfire Count Cylinder #1 to #4: Misfire count according to cylinder.
-
Catalyst OT Misfire Fuel Cut Cylinder #1 to #4: This expresses a high-frequency misfire was concentrated in a certain cylinder and that cylinder's fuel injection was stopped.
-
If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
-
If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as Freeze Frame Data.
-
If the misfire still cannot be reproduced even though the conditions stored in the ECM as Freeze Frame Data have been reproduced, one of the following factors is considered to be a possible cause of the problem:
-
There was insufficient fuel in the tank.
-
Improper fuel was used.
-
The spark plugs have been contaminated.
-
The problem requires further diagnosis.
-
After finishing repairs, check the misfire counts of the cylinders (Misfire Count Cylinder #1 to Misfire Count Cylinder #4).
-
Be sure to confirm that no misfiring cylinder DTCs are stored again by performing the confirmation driving pattern after finishing repairs.
-
When one of Short FT B1S1, Long FT B1S1 in the Freeze Frame Data is outside the range of +/-20%, the air fuel ratio may be rich (-20% or less) or lean (+20% or higher).
-
When Coolant Temperature in the Freeze Frame Data is less than 75°C (167°F), the misfires have occurred only while warming up the engine.
-
Vehicle body vibration caused by an extremely imbalanced drive wheel may cause misfire DTCs to be stored.
-
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
1.
|
CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Trouble Codes.
(e) Read the DTCs.
Powertrain > Engine > Trouble Codes
Result
|
Proceed to
|
DTC P030000, P030027, P030085, P030100, P030200, P030300 and/or P030400 are output
|
A
|
DTC P030000, P030027, P030085, P030100, P030200, P030300 and/or P030400 and other DTCs are output
|
B
|
HINT:
If any DTCs other than P030000, P030027, P030085, P030100, P030200, P030300 and/or P030400 are output, troubleshoot those DTCs first.
A
|
|
|
2.
|
CHECK PCV VALVE AND HOSE CONNECTIONS
|
(a) Check the PCV hose connections.
(b) Check the PCV valve.
Click here
OK:
PCV hose and PCV valve are connected correctly and are not damaged.
NG |
|
REPAIR OR REPLACE PCV VALVE OR HOSE
|
OK
|
|
|
3.
|
READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List / Misfire RPM and Misfire Load.
Powertrain > Engine > Data List
Tester Display
|
Misfire RPM
|
Misfire Load
|
(e) Read and note the Misfire RPM and Misfire Load values.
HINT:
The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.
NEXT
|
|
|
4.
|
READ VALUE USING TECHSTREAM (CATALYST OT MISFIRE FUEL CUT)
|
(a) Enter the following menus: Powertrain / Engine / Data List / Catalyst OT Misfire Fuel Cut.
Powertrain > Engine > Data List
Tester Display
|
Catalyst OT Misfire Fuel Cut
|
(b) Read the value displayed on the Techstream.
Data List
|
Result
|
Proceed to
|
Catalyst OT Misfire Fuel Cut
|
Avail
|
A
|
Not Avi
|
B
|
A
|
|
|
5.
|
READ FREEZE FRAME DATA (CATALYST OT MISFIRE FUEL CUT HISTORY)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Using the Techstream, confirm the vehicle conditions recorded in the Freeze Frame Data which were present when the DTC was stored.
Click here
Freeze Frame Data Item
|
Result
|
Proceed to
|
Catalyst OT Misfire Fuel Cut History
|
ON
|
A
|
OFF
|
B
|
A
|
|
|
6.
|
CHECK MISFIRE COUNT OF PORT INJECTION
|
(a) Connect the Techstream to the DLC3.
(b) Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Active Test / Prohibit the Catalyst OT Misfire Prevent Fuel Cut / Data List / Coolant Temperature, Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #4.
Powertrain > Engine > Active Test
Active Test Display
|
Prohibit the Catalyst OT Misfire Prevent Fuel Cut
|
Data List Display
|
Coolant Temperature
|
Injection Mode
|
Misfire Count Cylinder #1
|
Misfire Count Cylinder #2
|
Misfire Count Cylinder #3
|
Misfire Count Cylinder #4
|
(e) Read each value for Misfire Count Cylinder #1 to Misfire Count Cylinder #4 and Injection Mode displayed on the Techstream while performing the Active Test.
Injection Mode
|
Misfire Count
|
Proceed to
|
Port
|
1 or 2 cylinders have misfire counts
|
A
|
3 cylinders or more have misfire counts
|
There are no misfire counts
|
B
|
7.
|
CHECK MISFIRE COUNT OF PORT INJECTION
|
(a) Connect the Techstream to the DLC3.
(b) Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Data List / Coolant Temperature, Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #4.
Powertrain > Engine > Active Test
Active Test Display
|
Control the Injection Mode
|
Data List Display
|
Coolant Temperature
|
Injection Mode
|
Misfire Count Cylinder #1
|
Misfire Count Cylinder #2
|
Misfire Count Cylinder #3
|
Misfire Count Cylinder #4
|
(e) According to the display on the Techstream, read the Data List with the Active Test "Control the Injection Mode" set to Port. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.
(1) Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedures above [A].
(2) Read the Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #4 or DTCs displayed on the Techstream [B].
Injection Mode
|
Misfire Count
|
Proceed to
|
Port
|
1 or 2 cylinders have misfire counts
|
A
|
3 cylinders or more have misfire counts
|
There are no misfire counts
|
B
|
A
|
|
|
8.
|
CHECK MISFIRE COUNT OF DIRECT INJECTION
|
(a) Connect the Techstream to the DLC3.
(b) Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Data List / Coolant Temperature, Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #4.
Powertrain > Engine > Active Test
Active Test Display
|
Control the Injection Mode
|
Data List Display
|
Coolant Temperature
|
Injection Mode
|
Misfire Count Cylinder #1
|
Misfire Count Cylinder #2
|
Misfire Count Cylinder #3
|
Misfire Count Cylinder #4
|
(e) According to the display on the Techstream, read the Data List with the Active Test "Control the Injection Mode" set to Direct. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.
(1) Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedures above [A].
(2) Read the Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #4 or DTCs displayed on the Techstream [B].
Misfire Count
|
Proceed to
|
Port (Result of step 6 or 7)
|
Direct
|
1 or 2 cylinders have misfire counts
|
1 or 2 cylinders have misfire counts
|
A
|
3 cylinders or more have misfire counts
|
3 cylinders or more have misfire counts
|
B
|
1 or 2 cylinders have misfire counts
|
There are no misfire counts
|
C
|
3 cylinders or more have misfire counts
|
There are no misfire counts
|
D
|
HINT:
Perform "Inspection After Repair" after replacing the port fuel injector assembly.
Click here
D
|
|
|
9.
|
CHECK FUEL PRESSURE (FOR LOW PRESSURE SIDE)
|
(a) Check the fuel pressure (for low pressure side).
Click here
HINT:
Perform "Inspection After Repair" after replacing the port fuel injector assembly.
Click here
NG
|
|
|
(a) Check the fuel lines for leaks or blockage.
HINT:
Perform "Inspection After Repair" after replacing the fuel pump (for low pressure side).
Click here
NG |
|
REPAIR OR REPLACE FUEL SYSTEM
|
11.
|
CHECK MISFIRE COUNT OF DIRECT INJECTION
|
(a) Connect the Techstream to the DLC3.
(b) Start the engine and warm it up until the engine coolant temperature reaches 80°C (176°F) or higher.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Mode / Data List / Coolant Temperature, Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #4.
Powertrain > Engine > Active Test
Active Test Display
|
Control the Injection Mode
|
Data List Display
|
Coolant Temperature
|
Injection Mode
|
Misfire Count Cylinder #1
|
Misfire Count Cylinder #2
|
Misfire Count Cylinder #3
|
Misfire Count Cylinder #4
|
(e) According to the display on the Techstream, read the Data List with the Active Test "Control the Injection Mode" set to Direct. If no misfire counts occur in any cylinders, perform procedure [A] and [B] and then check the misfire counts again.
(1) Drive the vehicle with the Misfire RPM and Misfire Load noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedures above [A].
(2) Read the Injection Mode and Misfire Count Cylinder #1 to Misfire Count Cylinder #4 or DTCs displayed on the Techstream [B].
Misfire Count
|
Proceed to
|
Port (Result of step 6 or 7)
|
Direct
|
There are no misfire counts
|
There are misfire counts
|
A
|
There are no misfire counts
|
There are no misfire counts
|
B
|
HINT:
Perform "Inspection After Repair" after replacing the direct fuel injector assembly.
Click here
B
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(e) Turn the ignition switch off and wait for at least 30 seconds.
NEXT
|
|
|
(a) Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
(b) Turn the Techstream on.
(c) Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature, Injection Mode, Misfire Count Cylinder #1 to Misfire Count Cylinder #4, Misfire RPM and Misfire Load.
Powertrain > Engine > Data List
Tester Display
|
Coolant Temperature
|
Injection Mode
|
Misfire Count Cylinder #1
|
Misfire Count Cylinder #2
|
Misfire Count Cylinder #3
|
Misfire Count Cylinder #4
|
Misfire RPM
|
Misfire Load
|
(d) Drive the vehicle with Misfire RPM and Misfire Load.
(e) Monitor all of the misfire count values and Injection Mode displayed on the Techstream.
Misfire Count
|
Injection Mode
|
Proceed to
|
There are no misfire counts
|
-
|
A
|
1 or 2 cylinders have misfire counts
|
Port or Either
|
B
|
3 cylinders or more have misfire counts
|
Port or Either
|
C
|
There are misfire counts
|
Direct
|
D
|
HINT:
Perform "Inspection After Repair" after replacing the direct fuel injector assembly.
Click here
B
|
|
|
(a) Inspect the spark plug of the misfiring cylinder.
Click here
HINT:
Perform "Inspection After Repair" after replacing the spark plug.
Click here
OK
|
|
|
15.
|
CHECK FOR SPARK (SPARK TEST)
|
(a) Perform a spark test.
Click here
HINT:
-
If the result of the spark test is normal, proceed to the next step.
-
Perform "Inspection After Repair" after replacing the spark plug or ignition coil assembly.
Click here
NEXT
|
|
|
16.
|
CHECK CYLINDER COMPRESSION PRESSURE
|
(a) Measure the cylinder compression pressure of the misfiring cylinder.
Click here
HINT:
Perform "Inspection After Repair" after repairing or replacing the engine assembly.
Click here
NG |
|
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
|
(a) Check the intake system for vacuum leaks.
Click here
OK:
No leaks from intake system.
HINT:
Perform "Inspection After Repair" after repairing or replacing the intake system.
Click here
NG |
|
REPAIR OR REPLACE INTAKE SYSTEM
|
OK
|
|
|
18.
|
READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List / Coolant Temperature.
Powertrain > Engine > Data List
Tester Display
|
Coolant Temperature
|
(e) Read the Data List twice, when the engine is both cold and warmed up.
Standard:
Techstream Display
|
Condition
|
Specified Condition
|
Coolant Temperature
|
Cold engine
|
Same as ambient air temperature
|
Warm engine
|
Between 75 and 100°C (167 and 212°F)
|
HINT:
Perform "Inspection After Repair" after replacing the engine coolant temperature sensor.
Click here
OK
|
|
|
19.
|
READ VALUE USING TECHSTREAM (MASS AIR FLOW SENSOR)
|
(a) Connect the Techstream to the DLC3.
(b) Start the engine.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Engine / Data List / Engine Speed, Mass Air Flow Sensor and Coolant Temperature.
Powertrain > Engine > Data List
Tester Display
|
Engine Speed
|
Mass Air Flow Sensor
|
Coolant Temperature
|
(e) Allow the engine to idle until Coolant Temperature reaches 75°C (167°F) or higher.
(f) Read Mass Air Flow Sensor while maintaining an engine speed of 3000 rpm.
Standard:
Techstream Display
|
Condition
|
Specified Condition
|
Mass Air Flow Sensor
|
Engine warmed up
Shift position: P
A/C: Off
Engine Speed: 3000 rpm
|
Between 7.5 and 12.5 gm/sec
|
OK
|
|
|
20.
|
PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE EGR STEP POSITION)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher.
HINT:
The A/C switch and all accessories should be off.
(e) Enter the following menus: Powertrain / Engine / Active Test / Control the EGR Step Position / Data List / Engine Speed, Intake Manifold Absolute Pressure and Coolant Temperature.
Powertrain > Engine > Active Test
Active Test Display
|
Control the EGR Step Position
|
Data List Display
|
Engine Speed
|
Intake Manifold Absolute Pressure
|
Coolant Temperature
|
(f) Check the engine idling condition and Intake Manifold Absolute Pressure values in the Data List while performing the Active Test.
NOTICE:
-
Do not leave the EGR valve open for 10 seconds or more during the Active Test.
-
Be sure to return the EGR valve to step 0 when the Active Test is completed.
-
Do not open the EGR valve 30 steps or more during the Active Test.
OK:
The value of Intake Manifold Absolute Pressure and Engine Speed change in response to EGR step position.
Standard:
-
|
Control the EGR Step Position (Active Test)
|
0 Steps
|
0 to 30 Steps
|
Idling condition
|
Steady idling
|
Idling changes from steady to rough idling or engine stalls
|
Intake Manifold Absolute Pressure
(Data List)
|
Intake Manifold Absolute Pressure value is 20 to 40 kPa(abs)
(2.9 to 5.8 psi(abs))
(EGR valve is fully closed)
|
Intake Manifold Absolute Pressure value is at least +10 kPa (1.45 psi) higher than when EGR valve is fully closed
|
HINT:
During Active Test, if the idling condition does not change in response to EGR step position, then there is probably a malfunction in the EGR valve.
NG
|
|
|
21.
|
INSPECT EGR VALVE ASSEMBLY
|
(a) Remove the EGR valve assembly.
Click here
(b) Check if the EGR valve is stuck open.
OK:
EGR valve is tightly closed.
HINT:
Perform "Inspection After Repair" after replacing the EGR valve assembly.
Click here
OK
|
|
|
22.
|
CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TEETH ON TIMING CHAIN)
|
*a
|
Timing Mark
|
*b
|
TDC Timing Mark
|
*c
|
Groove
|
(a) Remove the cylinder head cover sub-assembly.
Click here
(b) Turn the crankshaft pulley and align its groove with the TDC timing mark of the timing chain cover.
(c) Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.
HINT:
If the timing marks are not as shown, turn the crankshaft one revolution clockwise.
OK:
Timing marks on camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.
HINT:
If the result is not as specified, check for mechanical malfunctions that may have affected the valve timing, such as a jumped tooth or stretching of the timing chain.
NG
|
|
|
23.
|
CHECK ENGINE MECHANICAL SYSTEM
|
(a) Check for mechanical malfunctions that affect the valve timing, such as a jumped tooth or stretching of the timing chain.
HINT:
Perform "Inspection After Repair" after repairing or replacing the engine mechanical system.
Click here
NG |
|
REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA
|
OK
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(e) Turn the ignition switch off and wait for at least 30 seconds.
NEXT
|
|
|
25.
|
CONFIRM WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
|
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Powertrain > Engine > Utility
Tester Display
|
All Readiness
|
(c) Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300 or P030400.
(d) Check the DTC judgment result.
Result
|
Proceed to
|
NORMAL
(DTCs are not output)
|
A
|
ABNORMAL
(DTC P030000, P030027, P030085, P030100, P030200, P030300 and/or P030400 is output)
|
B
|
26.
|
CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION)
|
(a) Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM.
Click here
HINT:
Repair any problems.
NEXT
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(e) Turn the ignition switch off and wait for at least 30 seconds.
NEXT
|
|
|
28.
|
CHECK WHETHER DTC OUTPUT RECURS (MISFIRE DTCS)
|
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Powertrain > Engine > Utility
Tester Display
|
All Readiness
|
(c) Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300 or P030400.
(d) Check the DTC judgment result.
Result
|
Proceed to
|
NORMAL
(DTCs are not output)
|
A
|
ABNORMAL
(DTC P030000, P030027, P030085, P030100, P030200, P030300 and/or P030400 is output)
|
B
|
A |
|
END
|
B
|
|
|
29.
|
CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
|
(a) Disconnect the mass air flow meter sub-assembly connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance (except TMMK Made):
Tester Connection
|
Condition
|
Specified Condition
|
C30-3 (5V) - C57-78 (VCVG)
|
Always
|
Below 1 Ω
|
C30-1 (FG) - C57-101 (VG)
|
Always
|
Below 1 Ω
|
C30-2 (E2G) - C57-79 (E2G)
|
Always
|
Below 1 Ω
|
C30-3 (5V) or C57-78 (VCVG) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
C30-1 (FG) or C57-101 (VG) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
C30-2 (E2G) or C57-79 (E2G) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
Standard Resistance (for TMMK Made):
Tester Connection
|
Condition
|
Specified Condition
|
C30-3 (5V) - C100-78 (VCVG)
|
Always
|
Below 1 Ω
|
C30-1 (FG) - C100-101 (VG)
|
Always
|
Below 1 Ω
|
C30-2 (E2G) - C100-79 (E2G)
|
Always
|
Below 1 Ω
|
C30-3 (5V) or C100-78 (VCVG) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
C30-1 (FG) or C100-101 (VG) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
C30-2 (E2G) or C100-79 (E2G) - Body ground and other terminals
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
30.
|
REPLACE MASS AIR FLOW METER SUB-ASSEMBLY
|
(a) Replace the mass air flow meter sub-assembly.
Click here
HINT:
-
If the results of the inspections performed in step 19 (READ VALUE USING TECHSTREAM (MASS AIR FLOW SENSOR)) indicated no problem, proceed to the next step without replacing the mass air flow meter sub-assembly.
-
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Click here
NEXT
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(e) Turn the ignition switch off and wait for at least 30 seconds.
NEXT
|
|
|
32.
|
CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
|
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Powertrain > Engine > Utility
Tester Display
|
All Readiness
|
(c) Input the DTC: P030000, P030027, P030085, P030100, P030200, P030300 or P030400.
(d) Check the DTC judgment result.
Result
|
Proceed to
|
NORMAL
(DTCs are not output)
|
A
|
ABNORMAL
(DTC P030000, P030027, P030085, P030100, P030200, P030300 and/or P030400 is output)
|
B
|
A |
|
END
|
|