- Occupant classification system
- Passenger airbag ON/OFF indicator
- Airbag system (Front passenger side)
- Seat belt warning system (Front passenger)
| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000014TRR |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [06/2017 - 10/2020] |
| Title: SUPPLEMENTAL RESTRAINT SYSTEMS: FRONT SEAT SIDE AIRBAG ASSEMBLY (for TMMK Made): REMOVAL; 2018 - 2020 MY Camry [06/2017 - 10/2020] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during front seat airbag assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Removal/installation of the front passenger seat |
Zero point calibration (Occupant classification system) |
|
|
|
Disconnect cable from negative battery terminal |
Perform steering sensor zero point calibration |
Lane departure alert system (w/ Steering Control) |
|
|
Pre-collision system |
|||
|
Intelligent clearance sonar system* |
|||
|
Memorize steering angle neutral point |
Parking assist monitor system |
|
|
|
Panoramic view monitor system |
|
||
-
Be sure to read Precaution thoroughly before servicing.
Click here
![2018 - 2019 MY Camry [06/2017 - 09/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
- Wear protective gloves. Sharp areas on the parts may injure your hands.
NOTICE:
If a front seat airbag assembly has been deployed, replace the front seat airbag assembly, front seatback frame sub-assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.
for Manual Seat: Click here
for Power Seat: Click here
PROCEDURE
1. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)
Click here
2. REMOVE FRONT SEAT ASSEMBLY (for Power Seat)
Click here
3. DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER (for Manual Seat)
Click here
4. DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER (for Power Seat)
Click here
5. REMOVE VERTICAL ADJUSTING HANDLE (for Manual Seat)
Click here
6. REMOVE RECLINING ADJUSTER RELEASE HANDLE (for Manual Seat)
Click here
7. REMOVE FRONT SEAT FRONT CUSHION SHIELD (for Power Seat)
Click here
8. REMOVE FRONT SEAT CUSHION SHIELD (for Manual Seat)
Click here
9. REMOVE FRONT SEAT CUSHION SHIELD (for Power Seat)
Click here
10. REMOVE FRONT SEAT INNER CUSHION SHIELD (for Manual Seat)
Click here
11. REMOVE FRONT SEAT INNER CUSHION SHIELD (for Power Seat)
Click here
12. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (for Manual Seat)
Click here
13. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (for Power Seat)
Click here
14. REMOVE FRONT SEAT HEADREST SUPPORT (for Manual Seat)
Click here
15. REMOVE FRONT SEAT HEADREST SUPPORT (for Power Seat)
Click here
16. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Manual Seat)
Click here
17. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD (for Power Seat)
Click here
18. REMOVE FRONT SEAT AIRBAG ASSEMBLY
CAUTION:
When storing the front seat airbag assembly, keep the airbag deployment side facing upward.
|
Deployment Side |
|
(a) Disengage the clamp. |
|
(b) Remove the 2 nuts and front seat airbag assembly.
NOTICE:
- Do not reuse the nuts.
- Make sure that the front seatback frame sub-assembly is not deformed. If it is deformed, replace it with a new one.
|
|