- Measurement of ultrasonic sensor detection angle
- Ultrasonic sensor detection angle registration
| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000014TM5 |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [06/2017 - 10/2020] |
| Title: PARK ASSIST / MONITORING: ULTRASONIC SENSOR (for Rear): REMOVAL; 2018 - 2020 MY Camry [06/2017 - 10/2020] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during ultrasonic sensor removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
Ultrasonic sensor |
|
|
|
HINT:
- Use the same procedure for the RH side and LH side.
- The following procedure is for the LH side.
PROCEDURE
1. REMOVE REAR BUMPER ASSEMBLY
Click here
![2018 - 2020 MY Camry [06/2017 - 10/2020]; EXTERIOR PANELS / TRIM: REAR BUMPER: REMOVAL](/t3Portal/stylegraphics/info.gif)
2. REMOVE REAR CENTER ULTRASONIC SENSOR
(a) Disconnect the connector.
|
Remove in this Direction |
(b) Disengage the 4 claws as shown in the illustration.
(c) Disengage the 2 claws and remove the rear center ultrasonic sensor as shown in the illustration.
|
|
Remove in this Direction |
3. REMOVE REAR CORNER ULTRASONIC SENSOR
(a) Disconnect the connector.
|
|
Remove in this Direction |
(b) Disengage the 4 claws as shown in the illustration.
(c) Disengage the 2 claws and remove the rear corner ultrasonic sensor as shown in the illustration.
|
|
Remove in this Direction |
4. REMOVE ULTRASONIC SENSOR CLIP
HINT:
- Perform this procedure only when replacement of the ultrasonic sensor clip is necessary.
- Use the same procedure for all ultrasonic sensor clips.
|
(a) Disengage the clamp to remove the ultrasonic sensor clip from the wire. |
|
5. REMOVE REAR CENTER ULTRASONIC SENSOR RETAINER
HINT:
- Perform this procedure only when replacement of the rear center ultrasonic sensor retainer is necessary.
- When removing the rear center ultrasonic sensor retainer, heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light.
(a) Heat the rear bumper assembly and rear center ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.
Heating Temperature:
|
Item |
Temperature |
|---|---|
|
Rear Bumper Assembly |
40 to 60°C (104 to 140°F) |
|
Rear Center Ultrasonic Sensor Retainer |
CAUTION:
- Do not touch the heat light and heated parts.
- Touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
|
*a |
Heated Part |
|
*b |
Heat Light |
|
(b) Remove the rear center ultrasonic sensor retainer. |
|
6. REMOVE REAR CORNER ULTRASONIC SENSOR RETAINER
HINT:
- Perform this procedure only when replacement of the rear corner ultrasonic sensor retainer is necessary.
- When removing the rear corner ultrasonic sensor retainer, heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light.
(a) Heat the rear bumper assembly and rear corner ultrasonic sensor retainer using a heat light at the specified temperature for 3 to 5 minutes.
Heating Temperature:
|
Item |
Temperature |
|---|---|
|
Rear Bumper Assembly |
40 to 60°C (104 to 140°F) |
|
Rear Corner Ultrasonic Sensor Retainer |
CAUTION:
- Do not touch the heat light and heated parts.
- Touching the heat light may result in burns.
- Touching heated parts for a long time may result in burns.
|
*a |
Heated Part |
|
*b |
Heat Light |
|
(b) Remove the rear corner ultrasonic sensor retainer. |
|
|
|