| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000014TKA |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [06/2017 - ] |
| Title: AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: Parking Brake Switch Circuit; 2018 - 2024 MY Camry [06/2017 - ] | ||
|
Parking Brake Switch Circuit |
DESCRIPTION
This circuit is from the parking brake switch assembly*1 or skid control ECU (Brake Actuator Assembly)*2 to the radio and display receiver assembly.
-
*1: w/o Electric Parking Brake System
*2: w/ Electric Parking Brake System
WIRING DIAGRAM
w/o Electric Parking Brake System
w/ Electric Parking Brake System
PROCEDURE
|
1. |
CHECK MODEL |
(a) Choose the model to be inspected.
|
Result |
Proceed to |
|---|---|
|
w/o Electric Parking Brake System |
A |
|
w/ Electric Parking Brake System |
B |
| B |
|
|
|
2. |
CHECK BRAKE WARNING LIGHT |
(a) Check that the brake warning light comes on when the parking brake is applied and goes off when it is released.
OK:
The brake warning light operates as specified above.
| NG |
|
GO TO BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS
|
![2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/o Electric Parking Brake System): HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
|
|
3. |
CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH ASSEMBLY - RADIO AND DISPLAY RECEIVER ASSEMBLY) |
(a) Disconnect the K2 radio and display receiver assembly connector.
(b) Disconnect the A4 parking brake switch assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K2-20 (PKB) - A4-1 |
Always |
Below 1 Ω |
|
K2-20 (PKB) or A4-1 - Body ground |
Always |
10 kΩ or higher |
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
4. |
CHECK BRAKE WARNING LIGHT |
(a) Check that the brake warning light comes on when the parking brake is applied and goes off when it is released.
OK:
The brake warning light operates as specified above.
| NG |
|
GO TO BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS
|
|
|
5. |
CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) - RADIO AND DISPLAY RECEIVER ASSEMBLY) |
(a) Disconnect the K2 radio and display receiver assembly connector.
(b) Disconnect the A34 skid control ECU (brake actuator assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K2-20 (PKB) - A34-33 (PKB) |
Always |
Below 1 Ω |
|
K2-20 (PKB) or A34-33 (PKB) - Body ground |
Always |
10 kΩ or higher |
| OK |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|