| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000014TFR |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [06/2017 - 10/2020] |
| Title: CRUISE CONTROL: DYNAMIC RADAR CRUISE CONTROL SYSTEM: Cruise SET Indicator Light Circuit; 2018 - 2020 MY Camry [06/2017 - 10/2020] | ||
|
Cruise SET Indicator Light Circuit |
DESCRIPTION
The ECM illuminates the cruise SET indicator by sending indicator output demand signals to the combination meter assembly via CAN communication. The cruise SET indicator illuminates when the dynamic radar cruise control system is controlling vehicle speed. The cruise SET indicator light circuit uses CAN communication. If the cruise SET indicator is not functioning correctly, check for CAN communication DTCs before troubleshooting this circuit.
CAUTION / NOTICE / HINT
CAUTION:
Observe the following items for safety reasons when using the Techstream:
- Before using the Techstream, read the instruction manual.
-
Prevent the Techstream cable from being caught on the pedals, shift lever or steering wheel when driving with the Techstream connected to the vehicle.
-
When driving the vehicle for testing purposes, 2 people are required. One person should operate the Techstream while the other drives the vehicle.
NOTICE:
Before replacing the ECM, refer to Registration.
w/o Smart Key System:
![2018 - 2019 MY Camry [03/2017 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: IMMOBILISER SYSTEM (w/o Smart Key System): REGISTRATION](/t3Portal/stylegraphics/info.gif)
w/ Smart Key System:
PROCEDURE
|
1. |
PERFORM ACTIVE TEST USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(e) Perform "Active Test" according to the display on the Techstream.
Body Electrical > Combination Meter > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Multi Display All (White) |
Multi-information display (White display) |
ON |
- |
Body Electrical > Combination Meter > Active Test
|
Tester Display |
|---|
|
Multi Display All (White) |
|
Result |
Proceed to |
|---|---|
|
The multi-information display in the combination meter assembly turns on according to the operation of the Active Test. |
A |
|
The multi-information display in the combination meter assembly does not turn on according to the operation of the Active Test. |
B |
| B |
|
|
|
2. |
READ VALUE USING TECHSTREAM |
(a) Turn the dynamic radar cruise control system on using the cruise control main switch.
(b) Drive at a speed between approximately 40 km/h (25 mph) and 180 km/h (112 mph).
(c) Enter the following menus: Powertrain / Radar Cruise 1 / Data List.
(d) Read the Data List according to the display on the Techstream.
Powertrain > Cruise Control > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
-SET Switch |
-SET switch signal |
ON or OFF |
ON: -SET switch pushed OFF: -SET switch not pushed |
- |
Powertrain > Cruise Control > Data List
|
Tester Display |
|---|
|
-SET Switch |
|
Result |
Proceed to |
|---|---|
|
The cruise SET indicator illuminates and turns off according to the operation of the -SET switch. |
A |
|
The cruise SET indicator does not illuminate but the Data List item -SET Switch changes according to the operation of the -SET switch. |
B |
|
The cruise SET indicator does not illuminate and the Data List item -SET Switch does not change according to the operation of the -SET switch. |
C |
| A |
|
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE
|
| B |
|
| C |
|
REPLACE ECM for A25A-FKS: Click here
for 2GR-FKS: Click here
|
|
|