Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014T5I
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 - 09/2019]
Title: BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: BRAKE ACTUATOR: INSTALLATION; 2018 - 2019 MY Camry [06/2017 - 09/2019]

INSTALLATION

CAUTION / NOTICE / HINT

w/ Electric Parking Brake System:

HINT:

The parking brake indicator light blinks (red) when the engine switch is turned on after replacing the brake actuator assembly. Operate the electric parking brake switch assembly to turn off the parking brake indicator light.

PROCEDURE

1. INSTALL BRAKE ACTUATOR BOLT CUSHION

(a) Install the brake actuator bolt cushion to the brake actuator bracket assembly.

2. INSTALL NO. 2 BRAKE ACTUATOR CASE COLLAR

(a) Install the No. 2 brake actuator case collar to the brake actuator bolt cushion.

NOTICE:

Make sure that the No. 2 brake actuator case collar is in full contact with the brake actuator bolt cushion.

3. INSTALL BRAKE ACTUATOR ASSEMBLY

(a) Install the brake actuator assembly to the brake actuator bracket assembly.

(b) Tighten the 2 nuts and install the bolt.

Torque:

6.5 N·m {66 kgf·cm, 58 in·lbf}

NOTICE:

  • Do not remove the hole plugs of a new brake actuator assembly before connecting the brake tubes because the brake actuator assembly is filled with brake fluid.
  • Do not hold the brake actuator assembly by the connector.
  • Do not drop the brake actuator assembly when carrying it.
  • Tighten the bolt and 2 nuts in the order shown in the illustration.

4. INSTALL BRAKE ACTUATOR WITH BRACKET

(a) w/ cushion:

(1) Temporarily install the brake actuator with bracket to the vehicle body.

NOTICE:

  • Do not kink or damage the brake lines.
  • Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
  • Be careful not to allow any brake fluid to enter the connector.
  • Do not hold the brake actuator assembly by the connector.
  • Do not drop the brake actuator with bracket when carrying it.

HINT:

  • Install the brake actuator with bracket while avoiding the brake lines.
  • After temporarily installing the brake actuator with bracket to the vehicle body, confirm that the cushion is contacting the upper side of the side member.

*a

Stud Bolt

*b

Cushion

*c

Side Member

(2) Install the 2 bolts and nut in the order shown in the illustration.

Torque:

19 N·m {194 kgf·cm, 14 ft·lbf}

HINT:

Install the 2 bolts from the bottom of the vehicle.

(b) w/o cushion:

(1) Temporarily install the brake actuator with bracket to the vehicle body with the 2 bolts and nut.

NOTICE:

  • Do not kink or damage the brake lines.
  • Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.
  • Be careful not to allow any brake fluid to enter the connector.
  • Do not hold the brake actuator assembly by the connector.
  • Do not drop the brake actuator with bracket when carrying it.

HINT:

  • Install the brake actuator with bracket while avoiding the brake lines.
  • Install the 2 bolts from the bottom of the vehicle.

(2) Fully tighten the 2 bolts and nut in the order shown in the illustration.

Torque:

19 N·m {194 kgf·cm, 14 ft·lbf}

(c) Remove the protective tape.

(d) Engage the clamp to install a new brake tube clamp.

(e) Return the front No. 3 brake tube to its original position.

NOTICE:

Do not apply excessive force to the front No. 3 brake tube.

(f) Temporarily install the front No. 3 brake tube to the front flexible hose.

NOTICE:

  • Do not kink or damage the front No. 3 brake tube.
  • Do not allow any foreign matter such as dirt or dust to enter the front No. 3 brake tube from the connecting parts.

(g) Engage the clamp to connect the front No. 3 brake tube.

NOTICE:

Do not kink or damage the front No. 3 brake tube.

(h) Temporarily tighten the brake line to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:

  • Do not kink or damage the brake line.
  • Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.

*a

To Front Wheel Cylinder Assembly LH

(i) Using a union nut wrench, fully tighten the brake line.

Torque:

Specified tightening torque :

15.2 N·m {155 kgf·cm, 11 ft·lbf}

NOTICE:

Do not kink or damage the brake line.

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

    13.4 N*m (137 kgf*cm, 10 ft.*lbf)

*a

Torque Wrench Fulcrum Length

*b

Union Nut Wrench

(j) Temporarily tighten the brake line to the correct position on the brake actuator assembly as shown in the illustration.

NOTICE:

  • Do not kink or damage the brake line.
  • Do not allow any foreign matter such as dirt or dust to enter the brake line from the connecting parts.

*a

To Rear Wheel Cylinder Assembly RH

(k) Using a union nut wrench, fully tighten the brake line.

Torque:

Specified tightening torque :

15.2 N·m {155 kgf·cm, 11 ft·lbf}

NOTICE:

Do not kink or damage the brake line.

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

    13.4 N*m (137 kgf*cm, 10 ft.*lbf)

*a

Torque Wrench Fulcrum Length

*b

Union Nut Wrench

(l) Temporarily tighten the 4 brake lines to the correct positions on the brake actuator assembly as shown in the illustration.

NOTICE:

  • Do not kink or damage the brake lines.
  • Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

*a

From 1st Chamber of Brake Master Cylinder Sub-assembly

*b

From 2nd Chamber of Brake Master Cylinder Sub-assembly

*c

To Front Wheel Cylinder Assembly RH

*d

To Rear Wheel Cylinder Assembly LH

(m) Using a union nut wrench, fully tighten each brake line.

Torque:

Specified tightening torque (A) :

19.5 N·m {199 kgf·cm, 14 ft·lbf}

Specified tightening torque (B) :

15.2 N·m {155 kgf·cm, 11 ft·lbf}

NOTICE:

Do not kink or damage the brake lines.

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

    (A): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)

  • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

    (B): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)

*a

Torque Wrench Fulcrum Length

*b

Union Nut Wrench

(n) Using a union nut wrench, fully tighten the front No. 3 brake tube while holding the front flexible hose with a wrench.

Torque:

Specified tightening torque :

15.2 N·m {155 kgf·cm, 11 ft·lbf}

NOTICE:

Do not kink or damage the front No. 3 brake tube.

HINT:

  • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

    Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

  • When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

    13.4 N*m (137 kgf*cm, 10 ft.*lbf)

*a

Torque Wrench Fulcrum Length

*b

Union Nut Wrench

(o) Connect the connector to the brake actuator assembly and lock the lock lever.

Connect the connector

Lock the lock lever

NOTICE:

  • Make sure that the connector is locked securely.
  • Make sure that the actuator connector can be connected smoothly.
  • Do not allow water, oil or dirt to enter the connector.

5. INSTALL FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

(a) Temporarily install the front center upper suspension brace sub-assembly with the 6 bolts and 4 nuts.

(b) Fully tighten the 2 nuts (A).

Torque:

50 N·m {510 kgf·cm, 37 ft·lbf}

(c) Fully tighten the 6 bolts and 2 nuts (B) to install the front center upper suspension brace sub-assembly.

Bolt:

Bolt Color

Torque

Black

8.0 N*m (82 kgf*cm, 71 in.*lbf)

Silver

8.9 N*m (91 kgf*cm, 79 in.*lbf)

Torque:

Nut (B) :

39 N·m {398 kgf·cm, 29 ft·lbf}

(d) Engage the 2 clamps to install the wire harness.

(e) Connect the connector.

6. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Click here 2018 - 2024 MY Camry [03/2017 -        ]; WIPER / WASHER: FRONT WIPER MOTOR: INSTALLATION+

7. INSTALL FRONT WHEEL RH

Click here 2018 - 2024 MY Camry [06/2017 -        ]; MAINTENANCE: TIRE AND WHEEL: INSTALLATION+

8. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

for A25A-FKS: Click here 2018 MY Camry [03/2017 - 08/2018]; MAINTENANCE: A25A-FKS BATTERY: INSTALLATION+ 2019 - 2024 MY Camry [08/2018 -        ]; MAINTENANCE: A25A-FKS BATTERY: INSTALLATION+

for 2GR-FKS: Click here 2018 - 2024 MY Camry [06/2017 -        ]; MAINTENANCE: 2GR-FKS BATTERY: INSTALLATION+

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 2018 MY Camry [06/2017 - 08/2018]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION 2019 MY Camry [08/2018 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: INITIALIZATION

9. BLEED BRAKE SYSTEM

Click here 2018 - 2024 MY Camry [03/2017 -        ]; BRAKE SYSTEM (OTHER): BRAKE FLUID: BLEEDING

10. PERFORM SYSTEM VARIANT LEARNING AND ACCELERATION SENSOR ZERO POINT CALIBRATION

w/o Electric Parking Brake System: Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/o Electric Parking Brake System): CALIBRATION

w/ Electric Parking Brake System: Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/ Electric Parking Brake System): CALIBRATION

11. PERFORM TEST MODE INSPECTION

w/o Electric Parking Brake System: Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/o Electric Parking Brake System): TEST MODE PROCEDURE

w/ Electric Parking Brake System: Click here 2018 - 2020 MY Camry [06/2017 - 03/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/ Electric Parking Brake System): TEST MODE PROCEDURE

12. INSPECT BRAKE ACTUATOR USING TECHSTREAM

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: BRAKE ACTUATOR: ON-VEHICLE INSPECTION

13. CHECK FOR AND CLEAR DTCS

w/o Electric Parking Brake System: Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/o Electric Parking Brake System): DTC CHECK / CLEAR

w/ Electric Parking Brake System: Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM (w/ Electric Parking Brake System): DTC CHECK / CLEAR