FRONT SUSPENSION: FRONT SHOCK ABSORBER: REMOVAL; 2018 - 2019 MY Camry [06/2017

Last Modified: 11-20-2023	6.11:8.1.0	Doc ID: RM1000000014T4E
Model Year Start: 2018	Model: Camry	Prod Date Range: [06/2017 - 09/2019]
Title: FRONT SUSPENSION: FRONT SHOCK ABSORBER: REMOVAL; 2018 - 2019 MY Camry [06/2017 - 09/2019]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front shock absorber assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function when Necessary Procedure not Performed	Link
Front wheel alignment adjustment	Perform system variant learning and acceleration sensor zero point calibration.	VSC disabled or malfunctioning DTCs are output Slip indicator light illuminated ABS warning light illuminated	w/ Electric Parking Brake System: w/o Electric Parking Brake System:
Suspension, tires, etc. (The vehicle height changes because of suspension or tire replacement)	Rear television camera assembly optical axis (Back camera position setting)	Parking assist monitor system	for Initialization: for Calibration:
	Measurement of ultrasonic sensor detection angle Ultrasonic sensor detection angle registration	Intelligent clearance sonar system Intuitive parking assist system
	Television camera controller initialization Adjust steering angle Rear television camera assembly optical axis (Back camera position setting)	Panoramic view monitor system	for Initialization: for Calibration:

HINT:

Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.

PROCEDURE

1. REMOVE FRONT WHEEL

Click here

2. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Click here

3. SEPARATE FRONT STABILIZER LINK ASSEMBLY

(a) Remove the nut and separate the front stabilizer link assembly from the front shock absorber assembly.

NOTICE:

Do not damage the boot of the ball joint.

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.

4. SEPARATE FRONT SPEED SENSOR

(a) Remove the bolt, disengage the clamp and separate the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.

5. LOOSEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

(a) Loosen the front support to front shock absorber nut.

CAUTION:

Only loosen the front support to front shock absorber nut if the front shock absorber with coil spring needs to be disassembled.
Only loosen the front support to front shock absorber nut, do not remove it.
If the front support to front shock absorber nut is removed with the front coil spring under tension, components of the front shock absorber with coil spring may fly off.

6. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

(a) Support the front lower No. 1 suspension arm sub-assembly using a jack and wooden block.

*a	Wooden Block
*b	Jack
	Front of the Vehicle
	Wooden Block Placement Location

NOTICE:

Keep the front lower No. 1 suspension arm sub-assembly supported until installation of the front shock absorber with coil spring is complete.

(b) Remove the 2 bolts and 2 nuts, and separate the front shock absorber with coil spring (lower side) from the steering knuckle.

NOTICE:

When removing the nuts, keep the bolts from rotating.
Use wire or an equivalent tool to hang the separated steering knuckle.

7. REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

(a) Secure SST in a vise.

SST: 09727-00051

SST: 09727-30022

09727-00010

09727-00031

(b) Attach the hooks of each SST arm across the diameter of the coil spring.

CAUTION:

Make sure that the hooks are securely attached to the coil spring.
If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.
Make sure that the hooks of the upper and lower SST arms are attached to the coil spring so that the distance between the hooks is as large as possible.
If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.
Make sure that the arms of SST are parallel and the number of coils between the arms is the same on each side.
If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

CAUTION:

Make sure that the stopper pins are installed securely.
If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

(d) Install SST and 2 vehicle nuts to the upper support as shown in the illustration.

SST: 09727-30022

09727-00090

09727-00100

*a	Vehicle Nut

(e) Using SST, compress the coil spring.

CAUTION:

If the coil spring starts to bow out while using SST, stop immediately and reattach SST correctly.
If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.
Do not compress the coil spring to the point where the coils touch each other.
If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.
Do not use an impact wrench.
If an impact wrench is used, the threads of SST may be damaged, or sudden compression of the coil spring may cause a hook to disengage and the coil spring to fly out, resulting in injury.
If a stopper pin touches the coil spring while using SST, remove the stopper pin and continue with the procedure.
If a stopper pin is removed, install a coil spring stopper belt as shown in the illustration.
If a hook disengages from the coil spring, the coil spring may fly out, resulting in injury.

SST: 09727-00110

(f) Check that the coil spring has become detached, and then remove the front support to front shock absorber nut.

CAUTION:

Do not remove the front support to front shock absorber nut while the coil spring is under tension.
If the front support to front shock absorber nut is removed with the coil spring under tension, components of the front shock absorber with coil spring may fly off, resulting in injury.

8. REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

(a) Remove the front suspension support sub-assembly from the front shock absorber assembly.

9. REMOVE STRUT MOUNTING BEARING WITH DUST COVER

(a) Disengage the end of the front No. 1 shock absorber dust cover from the claws of the front shock absorber assembly.

*1	Front No. 1 Shock Absorber Dust Cover
*a	Claw

(b) Remove the strut mounting bearing with dust cover from the front shock absorber assembly.

10. REMOVE FRONT UPPER COIL SPRING INSULATOR

(a) Remove the front upper coil spring insulator from the strut mounting bearing.

11. REMOVE STRUT MOUNTING BEARING

(a) Disengage the top end of the front No. 1 shock absorber dust cover to remove the strut mounting bearing from the shock absorber dust cover.

12. REMOVE FRONT COIL SPRING

(a) Remove the front coil spring and SST.

NOTICE:

Do not use an impact wrench. It will damage SST.

13. REMOVE FRONT SPRING BUMPER

(a) Remove the front spring bumper from the front shock absorber assembly.

14. REMOVE FRONT LOWER COIL SPRING INSULATOR

(a) Remove the front lower coil spring insulator from the front shock absorber assembly.

15. REMOVE SUSPENSION TOWER DAMPER (w/ Suspension Tower Damper)

(a) Remove the bolt and suspension tower damper from the front shock absorber assembly.

16. REMOVE FRONT SHOCK ABSORBER ASSEMBLY