Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000014T4B
Model Year Start: 2018 Model: Camry Prod Date Range: [06/2017 - 10/2020]
Title: BRAKE SYSTEM (OTHER): BRAKE BOOSTER: REMOVAL; 2018 - 2020 MY Camry [06/2017 - 10/2020]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake booster assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Intelligent clearance sonar system

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Panoramic view monitor system

2018 - 2020 MY Camry [06/2017 - 10/2020]; PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM: INITIALIZATION

CAUTION / NOTICE / HINT

NOTICE:

Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2018 - 2019 MY Camry [06/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry [03/2020 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE SYSTEM (OTHER): BRAKE MASTER CYLINDER: REMOVAL

3. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; INTERIOR PANELS / TRIM: INSTRUMENT PANEL SAFETY PAD: REMOVAL+

4. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Click here 2018 - 2024 MY Camry [03/2017 -        ]; WIPER / WASHER: FRONT WIPER MOTOR: REMOVAL

5. REMOVE FRONT CENTER UPPER SUSPENSION BRACE SUB-ASSEMBLY

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: BRAKE ACTUATOR: REMOVAL+

6. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (for A25A-FKS)

Click here 2018 MY Camry [06/2017 - 08/2018]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+ 2019 MY Camry [08/2018 - 09/2019]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+ 2020 MY Camry [09/2019 - 03/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+ 2020 MY Camry [03/2020 - 10/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

7. REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE (for A25A-FKS)

Click here 2018 MY Camry [06/2017 - 08/2018]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+ 2019 MY Camry [08/2018 - 09/2019]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+ 2020 MY Camry [09/2019 - 03/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+ 2020 MY Camry [03/2020 - 10/2020]; A25A-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

8. REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE (for 2GR-FKS)

Click here 2018 MY Camry [06/2017 - 08/2018]; 2GR-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+ 2019 - 2020 MY Camry [08/2018 - 10/2020]; 2GR-FKS (ENGINE MECHANICAL): ENGINE ASSEMBLY: REMOVAL+

9. REMOVE BATTERY CLAMP SUB-ASSEMBLY

(a) for A25A-FKS:

(1) Disengage the 4 clamps from the battery clamp sub-assembly.

(2) Remove the 3 bolts, nut and battery clamp sub-assembly.

(b) for 2GR-FKS:

(1) Disengage the 5 clamps from the battery clamp sub-assembly.

(2) Remove the 3 bolts, nut and battery clamp sub-assembly.

10. DISCONNECT UNION TO CHECK VALVE HOSE

(a) Slide the clip and disconnect the union to check valve hose from the brake booster assembly.

11. LOOSEN LOCK NUT

(a) Loosen the lock nut of the brake master cylinder push rod clevis.

*1

Lock Nut

*2

Brake Master Cylinder Push Rod Clevis

12. REMOVE PUSH ROD PIN

Click here 2018 - 2020 MY Camry [06/2017 - 10/2020]; BRAKE SYSTEM (OTHER): BRAKE PEDAL: REMOVAL+

13. REMOVE BRAKE BOOSTER ASSEMBLY

(a) Disconnect the connector from the vacuum warning switch assembly.

(b) Remove the 4 nuts and push the brake booster assembly toward the engine compartment.

NOTICE:

Do not apply excessive force to the brake lines.

(c) Remove the brake master cylinder push rod clevis and lock nut from the brake booster assembly.

(d) Remove the brake booster assembly from the vehicle body.

NOTICE:

Do not apply excessive force to the brake lines.

14. REMOVE BRAKE BOOSTER GASKET