Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM1000000013UQ6 |
Model Year Start: 2018 |
Model: Camry |
Prod Date Range: [03/2017 -
] |
Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function): Luggage Compartment Door Entry Unlock Function does not Operate when Key is Outside Luggage Compartment; 2018 - 2024 MY Camry [03/2017 - ] |
Luggage Compartment Door Entry Unlock Function does not Operate when Key is Outside Luggage Compartment
|
DESCRIPTION
If the entry luggage compartment door open function does not operate, there may be a malfunction in the luggage electrical key switch circuit or certification ECU (smart key ECU assembly), which receives a signal from the luggage electrical key switch circuit, or a communication error between the vehicle (electrical key antenna (outside luggage compartment)) and electrical key transmitter sub-assembly.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
HINT:
-
If the entry luggage compartment open functions does not operate, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).
-
If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether the malfunction was caused by wave interference.
Body Electrical > Smart Key > Utility
Tester Display
|
Operation History
|
PROCEDURE
1.
|
READ VALUE USING TECHSTREAM (LUGGAGE COMPARTMENT DOOR OPEN MODE)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Smart Key / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Smart Key > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Trunk Open Mode
|
Entry luggage compartment open mode
|
OFF or ON
|
Customize setting displayed
|
-
|
Body Electrical > Smart Key > Data List
Tester Display
|
Trunk Open Mode
|
Result
|
Proceed to
|
Trunk Open Mode is ON
|
A
|
Trunk Open Mode is OFF
|
B
|
A
|
|
|
2.
|
CHECK LUGGAGE COMPARTMENT DOOR OPENER SYSTEM
|
(a) Operate the luggage compartment door opening switch assembly in the vehicle and check that the luggage compartment door opens.
Click here
Result
|
Proceed to
|
The luggage compartment door opens
|
A
|
The luggage compartment door does not open
|
B
|
A
|
|
|
3.
|
READ VALUE USING TECHSTREAM (TR/B-DOOR UNLOCK SW)
|
(a) Connect the Techstream to the DLC3.
(b) Turn the engine switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Smart Key / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Smart Key > Data List
Tester Display
|
Measurement Item
|
Range
|
Normal Condition
|
Diagnostic Note
|
Tr/B-Door Unlock SW
|
Luggage electrical key switch
|
OFF or ON
|
OFF: Luggage electrical key switch not pushed
ON: Luggage electrical key switch pushed
|
-
|
Body Electrical > Smart Key > Data List
Tester Display
|
Tr/B-Door Unlock SW
|
OK:
The Techstream display changes correctly in response to the operation of the luggage electrical key switch.
OK
|
|
|
4.
|
CHECK WAVE ENVIRONMENT
|
(a) Bring the electrical key transmitter sub-assembly approximately 0.3 m (0.984 ft.) from the electrical key antenna (outside luggage compartment) and perform an entry luggage compartment open function check.
HINT:
-
Communication may not be possible if the electrical key transmitter sub-assembly is brought within 0.2 m (0.656 ft.) of the rear bumper.
-
When the electrical key transmitter sub-assembly is brought near the electrical key antenna (outside luggage compartment), the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
-
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
-
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
-
If a tool for checking radio waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
OK:
Entry functions operate normally.
|
|
*a
|
Approximately 0.3 m (0.984 ft.)
|
|
|
OK |
|
AFFECTED BY WAVE INTERFERENCE
|
NG
|
|
|
5.
|
CHECK KEY DIAGNOSTIC MODE
|
(a) Check the following antenna in key diagnostic mode.
Body Electrical > Smart Key > Utility
Tester Display
|
Communication Check(Key Diag Mode)
|
(b) When the electrical key transmitter sub-assembly is brought within 0.7 to 1 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage compartment), check that the wireless buzzer sounds.
HINT:
-
Select either channel 1 or channel 2 and inspect key diagnostic mode for each channel.
-
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
OK:
Wireless buzzer sounds.
|
|
*a
|
0.7 to 1.0 m (2.30 to 3.28 ft.)
|
|
|
NG
|
|
|
6.
|
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))
|
(a) Disconnect the R8 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the W2 electrical key antenna (outside luggage compartment) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
R8-13 (CLG8) - W2-2 (ANTE8)
|
Always
|
Below 1 Ω
|
R8-12 (CG8B) - W2-1 (CLGB)
|
Always
|
Below 1 Ω
|
R8-13 (CLG8) or W2-2 (ANTE8) - Other terminals and body ground
|
Always
|
10 kΩ or higher
|
R8-12 (CG8B) or W2-1 (CLGB) - Other terminals and body ground
|
Always
|
10 kΩ or higher
|
(d) Reconnect the R8 certification ECU (smart key ECU assembly) connector.
(e) Reconnect the W2 electrical key antenna (outside luggage compartment) connector.
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
7.
|
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE COMPARTMENT))
|
*a
|
Component with harness connected
(Certification ECU (Smart Key ECU Assembly))
|
*b
|
Waveform 1
|
(a) Using an oscilloscope, check the waveform.
OK:
Tester Connection
|
Condition
|
Tool Setting
|
Specified Condition
|
R8-13 (CLG8) - K62-18 (E)
|
Procedure:
-
Engine switch off
-
Electrical key transmitter sub-assembly brought outside vehicle
-
All doors closed
-
Luggage electrical key switch off → on
|
2 V/DIV., 500 ms/DIV.
|
Pulse generation
(See waveform 1)
|
R8-12 (CG8B) - K62-18 (E)
|
Procedure:
-
Engine switch off
-
Electrical key transmitter sub-assembly brought outside vehicle
-
All doors closed
-
Luggage electrical key switch off → on
|
2 V/DIV., 500 ms/DIV.
|
Pulse generation
(See waveform 1)
|
OK
|
|
|
8.
|
CHECK ENTRY LUGGAGE COMPARTMENT OPEN OPERATION
|
(a) Connect all connectors and check that the entry luggage compartment open function operates.
Click here
Result
|
Proceed to
|
Luggage open function operates normally
|
A
|
Luggage open function does not operate normally
|
B
|
A |
|
END (CONNECTOR WAS NOT CONNECTED SECURELY)
|
9.
|
INSPECT LUGGAGE ELECTRICAL KEY SWITCH
|
(a) Remove the luggage electrical key switch.
Click here
(b) Inspect the luggage electrical key switch.
Click here
OK
|
|
|
10.
|
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - LUGGAGE ELECTRICAL KEY SWITCH)
|
(a) Disconnect the R8 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the W1 luggage electrical key switch connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
R8-26 (TSW5) - W1-2
|
Always
|
Below 1 Ω
|
W1-1 - Body ground
|
Always
|
Below 1 Ω
|
R8-26 (TSW5) or W1-2 - Other terminals and body ground
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
11.
|
CHECK ENTRY LUGGAGE COMPARTMENT OPEN OPERATION
|
(a) Connect all connectors and check that the entry luggage compartment open function operates.
Click here
Result
|
Proceed to
|
Luggage open function operates normally
|
A
|
Luggage open function does not operate normally
|
B
|
A |
|
END (CONNECTOR WAS NOT CONNECTED SECURELY)
|
|