Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM10000000138AJ
Model Year Start: 2018 Model: Camry Prod Date Range: [03/2017 - 06/2017]
Title: A25A-FKS (ENGINE CONTROL): SFI SYSTEM: P05042B; Brake Switch "A"/"B" Signal Cross Coupled; 2018 MY Camry [03/2017 - 06/2017]

DTC

P05042B

Brake Switch "A"/"B" Signal Cross Coupled

DESCRIPTION

The stop light switch assembly is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch assembly and stores this DTC.

HINT:

The normal signal conditions are as shown in the table below.

Signal (ECM Terminal)

Brake Pedal Released

In Transition

Brake Pedal Depressed

STP

OFF

ON

ON

ST1-

ON

ON

OFF

  • [OFF] denotes ground potential.
  • [ON] denotes battery potential (+B).

On the Techstream, Data List item Stop Light SW is ON when the brake pedal is depressed.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

Note

P05042B

Brake Switch "A"/"B" Signal Cross Coupled

Conditions (a) and (b) are met for 0.5 seconds or more (1 trip detection logic):

(a) Ignition switch ON

(b) STP signal OFF when ST1- signal OFF

  • Open or short in stop light switch signal circuit
  • Stop light switch assembly
  • Instrument panel junction block assembly
  • ECM

Does not come on

DTC stored

SAE Code: P0504

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.

HINT:

  • Stop light switch assembly conditions can be checked using the Techstream.
    1. Connect the Techstream to the DLC3.
    2. Turn the ignition switch to ON.
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine / Data List / Stop Light SW.
    5. Check the Data List indication when the brake pedal is depressed and released.

      Brake Pedal Operation

      Stop Light SW

      Depressed

      ON

      Released

      OFF

  • Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE

1.

CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

*A

for 5 PIN Type Stop Light Switch

*B

for 7 PIN Type Stop Light Switch

*a

Front view of wire harness connector

(to Stop Light Switch Assembly)

-

-

(a) Disconnect the stop light switch assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

for 5 PIN Type Stop Light Switch

Tester Connection

Condition

Specified Condition

A38-1 (B) - Body ground

Always

11 to 14 V

for 7 PIN Type Stop Light Switch

Tester Connection

Condition

Specified Condition

A37-7 (B) - Body ground

Always

11 to 14 V

NG

GO TO STEP 13

OK

2.

CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

*A

for 5 PIN Type Stop Light Switch

*B

for 7 PIN Type Stop Light Switch

*a

Front view of wire harness connector

(to Stop Light Switch Assembly)

-

-

(a) Disconnect the stop light switch assembly connector.

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

for 5 PIN Type Stop Light Switch

Tester Connection

Condition

Specified Condition

A38-5 (B) - Body ground

Ignition switch ON

11 to 14 V

for 7 PIN Type Stop Light Switch

Tester Connection

Condition

Specified Condition

A37-6 (B) - Body ground

Ignition switch ON

11 to 14 V

NG

GO TO STEP 6

OK

3.

CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

(a) Disconnect the stop light switch assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for 5 PIN Type Stop Light Switch

Tester Connection

Condition

Specified Condition

A38-3 (GND) - Body ground

Always

Below 1 Ω

for 7 PIN Type Stop Light Switch

Tester Connection

Condition

Specified Condition

A37-2 (GND) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

4.

CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

*a

Brake Pedal Depressed

*b

Brake Pedal Released

*c

Front view of wire harness connector

(to ECM)

-

-

(a) Disconnect the ECM connector.

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Brake Pedal Operation

Specified Condition

A24-22 (ST1-) - Body ground

Released

7.5 to 14 V

Depressed

Below 1.5 V

A24-21 (STP) - Body ground

Released

Below 1.5 V

Depressed

7.5 to 14 V

OK

REPLACE ECM

NG

5.

CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)

(a) Disconnect the stop light switch assembly connector.

(b) Disconnect the ECM connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for 5 PIN Type Stop Light Switch

Tester Connection

Condition

Specified Condition

A38-4 (L) - A24-22 (ST1-)

Always

Below 1 Ω

A38-2 (L) - A24-21 (STP)

Always

Below 1 Ω

A38-4 (L) or A24-22 (ST1-) - Body ground and other terminals

Always

10 kΩ or higher

A38-2 (L) or A24-21 (STP) - Body ground and other terminals

Always

10 kΩ or higher

for 7 PIN Type Stop Light Switch

Tester Connection

Condition

Specified Condition

A37-5 (L) - A24-22 (ST1-)

Always

Below 1 Ω

A37-3 (L) - A24-21 (STP)

Always

Below 1 Ω

A37-5 (L) or A24-22 (ST1-) - Body ground and other terminals

Always

10 kΩ or higher

A37-3 (L) or A24-21 (STP) - Body ground and other terminals

Always

10 kΩ or higher

OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

(a) Disconnect the instrument panel junction block assembly connector.

(b) Disconnect the stop light switch assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for 5 PIN Type Stop Light Switch

Tester Connection

Condition

Specified Condition

3C-15 - A38-5 (B)

Always

Below 1 Ω

3C-15 or A38-5 (B) - Body ground and other terminals

Always

10 kΩ or higher

for 7 PIN Type Stop Light Switch

Tester Connection

Condition

Specified Condition

3C-15 - A37-6 (B)

Always

Below 1 Ω

3C-15 or A37-6 (B) - Body ground and other terminals

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

7.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

(a) Disconnect the instrument panel junction block assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3B-3 - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

8.

CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (POWER SOURCE)

*a

Front view of wire harness connector

(to Instrument Panel Junction Block Assembly)

(a) Disconnect the instrument panel junction block assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

3E-1 - Body ground

Always

11 to 14 V

Result

Proceed to

OK (w/ Smart Key System)

A

OK (w/o Smart Key System)

B

NG

C

B

GO TO STEP 11

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

A

9.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

(a) Disconnect the instrument panel junction block assembly connector.

(b) Disconnect the certification ECU (smart key ECU assembly) connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3A-17 - K62-17 (IG1D)

Always

Below 1 Ω

3A-17 or K62-17 (IG1D) - Body ground and other terminals

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

10.

CHECK SMART KEY SYSTEM

(a) Check the smart key system.

Click here 2018 - 2022 MY Camry [03/2017 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): HOW TO PROCEED WITH TROUBLESHOOTING

OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR SMART KEY SYSTEM

11.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - IGNITION SWITCH ASSEMBLY)

(a) Disconnect the instrument panel junction block assembly connector.

(b) Disconnect the ignition switch assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

3A-17 - K30-8 (IG1)

Always

Below 1 Ω

3A-17 or K30-8 (IG1) - Body ground and other terminals

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

12.

CHECK ECM POWER SOURCE CIRCUIT

(a) Check the ECM power source circuit.

Click here 2018 - 2024 MY Camry [03/2017 -        ]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM: ECM Power Source Circuit

OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR ECM POWER SOURCE CIRCUIT

13.

CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

(a) Disconnect the instrument panel junction block assembly connector.

(b) Disconnect the stop light switch assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

for 5 PIN Type Stop Light Switch

Tester Connection

Condition

Specified Condition

3C-3 - A38-1 (B)

Always

Below 1 Ω

3C-3 or A38-1 (B) - Body ground and other terminals

Always

10 kΩ or higher

for 7 PIN Type Stop Light Switch

Tester Connection

Condition

Specified Condition

3C-3 - A37-7 (B)

Always

Below 1 Ω

3C-3 or A37-7 (B) - Body ground and other terminals

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

14.

CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (POWER SOURCE)

*a

Front view of wire harness connector

(to Instrument Panel Junction Block Assembly)

(a) Disconnect the instrument panel junction block assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

3E-1 - Body ground

Always

11 to 14 V

OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)