Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM10000000138A3 |
Model Year Start: 2018 |
Model: Camry |
Prod Date Range: [03/2017 - 06/2017] |
Title: A25A-FKS (ENGINE CONTROL): SFI SYSTEM: P032515; Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open; 2018 MY Camry [03/2017 - 06/2017] |
DTC
|
P032515
|
Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open
|
DESCRIPTION
Refer to DTC P032511.
Click here
HINT:
When DTC P032515 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. Fail-safe mode continues until the ignition switch is turned off.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
MIL
|
Memory
|
Note
|
P032515
|
Knock Sensor 1 Bank 1 or Single Sensor Circuit Short to Battery or Open
|
The knock control sensor output voltage is higher than 4.5 V for 1 second or more (1 trip detection logic).
|
-
Open or short in knock control sensor circuit
-
Knock control sensor
-
ECM
|
Comes on
|
DTC stored
|
SAE Code: P0328
|
Reference: Inspection using an oscilloscope.
Click here
MONITOR DESCRIPTION
If the output voltage transmitted by the knock control sensor remains high for 1 second or more, the ECM interprets this as a malfunction in the sensor circuit, illuminates the MIL and stores this DTC.
MONITOR STRATEGY
Related DTCs
|
P0328: Knock control sensor range check (high voltage)
|
Required Sensors/Components (Main)
|
Knock control sensor
|
Required Sensors/Components (Related)
|
-
|
Frequency of Operation
|
Continuous
|
Duration
|
1 second
|
MIL Operation
|
Immediate
|
Sequence of Operation
|
None
|
TYPICAL ENABLING CONDITIONS
Monitor runs whenever the following DTCs are not stored
|
None
|
Both of the following conditions are met
|
-
|
Battery voltage
|
10.5 V or higher
|
Time after engine start
|
5 seconds or more
|
TYPICAL MALFUNCTION THRESHOLDS
Knock control sensor voltage
|
Higher than 4.5 V
|
CONFIRMATION DRIVING PATTERN
HINT:
-
After repair has been completed, clear the DTC and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.
Click here
-
When clearing the permanent DTCs, refer to the "CLEAR PERMANENT DTC" procedure.
Click here
-
Connect the Techstream to the DLC3.
-
Turn the ignition switch to ON.
-
Turn the Techstream on.
-
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
-
Turn the ignition switch off and wait for at least 30 seconds.
-
Start the engine and wait 5 minutes [A].
-
Turn the Techstream on.
-
Enter the following menus: Powertrain / Engine / Trouble Codes [B].
-
Read the pending DTCs.
HINT:
-
If a pending DTC is output, the system is malfunctioning.
-
If a pending DTC is not output, perform the following procedure.
-
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
-
Input the DTC: P032515.
-
Check the DTC judgment result.
Techstream Display
|
Description
|
NORMAL
|
-
DTC judgment completed
-
System normal
|
ABNORMAL
|
-
DTC judgment completed
-
System abnormal
|
INCOMPLETE
|
-
DTC judgment not completed
-
Perform driving pattern after confirming DTC enabling conditions
|
WIRING DIAGRAM
Refer to DTC P032511.
Click here
CAUTION / NOTICE / HINT
HINT:
Read Freeze Frame Data using the Techstream. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
1.
|
CHECK TERMINAL VOLTAGE (POWER SOURCE OF KNOCK CONTROL SENSOR)
|
*a
|
Front view of wire harness connector
(to Knock Control Sensor)
|
(a) Disconnect the knock control sensor connector.
(b) Turn the ignition switch to ON.
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
d3-2 - d3-1
|
Ignition switch ON
|
4.5 to 5.5 V
|
OK
|
|
|
2.
|
INSPECT KNOCK CONTROL SENSOR
|
(a) Inspect the knock control sensor.
Click here
HINT:
Perform "Inspection After Repair" after replacing the knock control sensor.
Click here
3.
|
CHECK HARNESS AND CONNECTOR (KNOCK CONTROL SENSOR - ECM)
|
(a) Disconnect the knock control sensor connector.
(b) Disconnect the ECM connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
d3-2 - C57-111 (KNK1)
|
Always
|
Below 1 Ω
|
d3-1 - C57-112 (EKNK)
|
Always
|
Below 1 Ω
|
d3-2 - C57-111 (KNK1) - Other terminals
|
Always
|
10 kΩ or higher
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Clear the DTCs.
Powertrain > Engine > Clear DTCs
(e) Turn the ignition switch off and wait for at least 30 seconds.
NEXT
|
|
|
5.
|
CHECK WHETHER DTC OUTPUT RECURS (DTC P032515)
|
(a) Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
(b) Enter the following menus: Powertrain / Engine / Trouble Codes.
(c) Read the DTCs.
Powertrain > Engine > Trouble Codes
Result
|
Proceed to
|
DTCs are not output
|
A
|
DTC P032515 is output
|
B
|
|