| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM10000000136FW |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [03/2017 - 08/2018] |
| Title: HEATING / AIR CONDITIONING: AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System): B1413; Evaporator Temperature Circuit or Evaporator Fin Thermistor; 2018 MY Camry [03/2017 - 08/2018] | ||
|
DTC |
B1413 |
Evaporator Temperature Circuit or Evaporator Fin Thermistor |
DESCRIPTION
The No. 1 cooler thermistor is installed to the evaporator in the air conditioner unit to detect the temperature of the cooled air that has passed through the evaporator, which is used to control the air conditioning system. It sends signals to the air conditioning amplifier assembly. The resistance of the No. 1 cooler thermistor changes in accordance with the temperature of the cooled air that has passed through the evaporator. As the temperature decreases, the resistance increases. As the temperature increases, the resistance decreases.
The air conditioning amplifier assembly applies voltage (5 V) to the No. 1 cooler thermistor and reads voltage changes as the resistance of the No. 1 cooler thermistor changes. This sensor is used for frost prevention.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Memory |
|---|---|---|---|---|
|
B1413 |
Evaporator Temperature Circuit or Evaporator Fin Thermistor |
Open or short in evaporator temperature sensor circuit |
|
Memorized (4 sec. or more)* |
- *: The air conditioning amplifier assembly stores this DTC if the malfunction has occurred for the period of time indicated in the brackets.
WIRING DIAGRAM
for Dual Type
for Single Type
PROCEDURE
|
1. |
READ VALUE USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Air Conditioner / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Air Conditioner > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Evaporator Fin Thermistor |
No. 1 cooler thermistor |
Min.: -29.70°C (-21.46°F) Max.: 59.55°C (139.19°F) |
Actual evaporator temperature displayed |
- |
Body Electrical > Air Conditioner > Data List
|
Tester Display |
|---|
|
Evaporator Fin Thermistor |
OK:
The display is as specified in the normal condition column.
| OK |
|
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
|
|
|
2. |
INSPECT NO. 1 COOLER THERMISTOR |
(a) Remove the No. 1 cooler thermistor.
Click here
![2018 MY Camry [03/2017 - 06/2017]; HEATING / AIR CONDITIONING: FRONT EVAPORATOR TEMPERATURE SENSOR: REMOVAL](/t3Portal/stylegraphics/info.gif)
(b) Inspect the No. 1 cooler thermistor.
Click here
| NG |
|
REPLACE NO. 1 COOLER THERMISTOR
|
|
|
3. |
INSPECT AIR CONDITIONING HARNESS ASSEMBLY |
|
*A |
for Dual Type |
*B |
for Single Type |
|
*a |
Air Conditioning Harness Assembly |
*b |
Front view of wire harness connector (to Air Conditioning Amplifier Assembly) |
|
*c |
Front view of wire harness connector (to No. 1 Cooler Thermistor) |
- |
- |
(a) Remove the air conditioning harness assembly.
Click here
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for Dual Type
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
z8-5 (SG) - 2 |
Always |
Below 1 Ω |
|
z8-6 (TE) - 1 |
Always |
Below 1 Ω |
Standard Resistance:
for Single Type
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
z9-5 (4A) - 2 |
Always |
Below 1 Ω |
|
z9-6 (5A) - 1 |
Always |
Below 1 Ω |
| OK |
|
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
|
| NG |
|
|
|