Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM10000000136DL
Model Year Start: 2018 Model: Camry Prod Date Range: [03/2017 - 06/2017]
Title: A25A-FKS (FUEL): FUEL MAIN VALVE: REMOVAL; 2018 MY Camry [03/2017 - 06/2017]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel main valve removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Replacement of fuel pump

Inspection after repair
  • Poor idle, etc.
  • Engine start function, etc.

2018 - 2019 MY Camry [03/2017 - 09/2019]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

CAUTION:

  • Never perform work on fuel system components near any possible ignition sources.
  • Vaporized fuel could ignite, resulting in a serious accident.
  • Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
  • Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

NOTICE:

  • Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.
  • When replacing the fuel filter, replace it together with the fuel suction plate sub-assembly.

*a

Tube

PROCEDURE

1. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Click here 2018 MY Camry [03/2017 - 06/2017]; A25A-FKS (FUEL): FUEL PUMP (for 2WD): REMOVAL

2. REMOVE FUEL SENDER GAUGE ASSEMBLY

Click here 2018 MY Camry [03/2017 - 06/2017]; A25A-FKS (FUEL): FUEL SENDER GAUGE ASSEMBLY: REMOVAL+

3. SEPARATE FUEL FILTER

(a) Disengage the clamp to disconnect the tube from the fuel filter.

(b) Using a screwdriver with its tip wrapped with protective tape, disengage the 3 claws.

*a

Protective Tape

(c) Using a screwdriver with its tip wrapped with protective tape, separate the fuel filter from the fuel sub-tank.

NOTICE:

  • Do not damage the fuel sub-tank and fuel filter.
  • Pull out the fuel filter carefully because the O-ring is firmly installed between the fuel filter and fuel sub-tank.
  • Do not do anything which may separate the tube from either the fuel suction plate sub-assembly or fuel filter, such as applying excessive force to the tube.

    Click here 2018 MY Camry [03/2017 - 06/2017]; A25A-FKS (FUEL): FUEL SYSTEM: PRECAUTION

*a

Protective Tape

(d) Remove the O-ring from the fuel sub-tank.

4. REMOVE FUEL MAIN VALVE ASSEMBLY (for Low Pressure)

(a) Remove the clip from the fuel filter.

(b) Using a screwdriver with its tip wrapped with protective tape, remove the fuel main valve assembly from the fuel filter.

NOTICE:

  • Pull out the fuel main valve assembly carefully because the O-rings are firmly installed between the fuel main valve assembly and fuel filter.
  • Do not damage the fuel filter.

*a

Protective Tape

(c) Remove the 2 O-rings from the fuel main valve assembly.

*1

O-ring

5. REMOVE FUEL MAIN VALVE ASSEMBLY (for High Pressure)

(a) Remove the clip from the fuel filter.

(b) Using a screwdriver with its tip wrapped with protective tape, remove the fuel main valve assembly from the fuel filter.

NOTICE:

  • Pull out the fuel main valve assembly carefully because the O-rings are firmly installed between the fuel main valve assembly and fuel filter.
  • Do not damage the fuel filter.

*a

Protective Tape

(c) Remove the O-ring from the fuel main valve assembly.

NOTICE:

Do not remove the mesh and mini-clip from the fuel main valve assembly.

*1

O-ring

*a

Mesh

*b

Mini-clip