Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000012W22
Model Year Start: 2018 Model: Camry Prod Date Range: [03/2017 - 06/2017]
Title: PRE-COLLISION: PRE-COLLISION SYSTEM: U0235; Lost Communication with Cruise Control Front Distance Range Sensor; 2018 MY Camry [03/2017 - 06/2017]

DTC

U0235

Lost Communication with Cruise Control Front Distance Range Sensor

DESCRIPTION

The millimeter wave radar sensor assembly is connected to the skid control ECU (brake actuator assembly) via CAN communication. If communication with the skid control ECU (brake actuator assembly) stops, the millimeter wave radar sensor assembly stores DTC U0235.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

U0235

Lost Communication with Cruise Control Front Distance Range Sensor

When the ignition switch is ON, a communication error between the millimeter wave radar sensor assembly and skid control ECU (brake actuator assembly) is detected for approximately 2 seconds.

  • Vehicle stability control system
  • Millimeter wave radar sensor assembly

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.
  • If the millimeter wave radar sensor assembly has been replaced, be sure to perform millimeter wave radar sensor assembly adjustment.

    Click here 2018 MY Camry [03/2017 - 06/2017]; CRUISE CONTROL: MILLIMETER WAVE RADAR SENSOR: ADJUSTMENT

  • The pre-collision system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

    Click here 2018 - 2024 MY Camry [03/2017 -        ]; NETWORKING: CAN COMMUNICATION SYSTEM: HOW TO PROCEED WITH TROUBLESHOOTING

PROCEDURE

1.

CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)

(a) Check for DTCs.

Chassis > ABS/VSC/TRAC > Trouble Codes

Result

Proceed to

Vehicle stability control system DTCs are not output

A

Vehicle stability control system DTCs are output

B

B

GO TO VEHICLE STABILITY CONTROL SYSTEM

A

2.

TEST MODE INSPECTION (VEHICLE STABILITY CONTROL SYSTEM)

HINT:

When entering Test Mode (Signal Check), the skid control ECU (brake actuator assembly) communicates with the millimeter wave radar sensor assembly to judge whether the vehicle is equipped with the pre-collision system. Therefore, do not exit Test Mode (Signal Check) within 5 seconds of entering Test Mode (Signal Check).

(a) Procedure to enter Test Mode

(1) Turn the ignition switch off.

(2) Check that the steering wheel is centered.

(3) Apply the parking brake.

(4) Check that the shift lever is in P.

(5) Connect the Techstream to the DLC3.

(6) Turn the ignition switch to ON.

(7) Turn the Techstream on.

(8) Switch the skid control ECU (brake actuator assembly) to Test Mode (Signal Check) using the Techstream. Enter the following menus: Chassis / ABS/VSC/TRAC / Utility / Signal Check.

HINT:

Do not exit Test Mode (Signal Check) within 5 seconds of entering Test Mode (Signal Check). If Test Mode (Signal Check) is exited within 5 seconds of entering Test Mode (Signal Check), DTC U0235 may be stored. If DTC U0235 is output after exiting Test Mode (Signal Check), enter Test Mode (Signal Check) again, wait at least 5 seconds, then recheck for DTCs.

Chassis > ABS/VSC/TRAC > Utility

Tester Display

Signal Check

(9) Check that the ABS warning and slip indicator lights come on for several seconds and then blink in the Test Mode (Signal Check) pattern.

HINT:

If the ABS warning and slip indicator lights do not blink, inspect the ABS warning and slip indicator light circuits.

(b) End Test Mode (Signal Check)

(1) Turn the ignition switch off to exit mode.

(2) Disconnect the Techstream.

NEXT

3.

CHECK FOR DTCs (PRE-COLLISION SYSTEM)

(a) Clear the DTCs.

Body Electrical > Pre-Collision 2 > Clear DTCs

(b) Perform the following procedure.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

  1. Turn the ignition switch to ON and wait 2 seconds or more.

(c) Check for DTCs.

Body Electrical > Pre-Collision 2 > Trouble Codes

Result

Proceed to

DTC U0235 is not output

A

DTC U0235 is output

B

A

END

B

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY