- Power source mode does not change when engine switch pressed
- Electrical key transmitter sub-assembly locked inside vehicle
| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000012VT5 |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [03/2017 - ] |
| Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): B27A6; Open in Rear Floor Electrical Key Oscillator Circuit; 2018 - 2024 MY Camry [03/2017 - ] | ||
|
DTC |
B27A6 |
Open in Rear Floor Electrical Key Oscillator Circuit |
DESCRIPTION
The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 1 indoor electrical key antenna assembly (rear floor). For the No. 1 indoor electrical key antenna assembly (rear floor) to detect when the electrical key transmitter sub-assembly is in the cabin, the signal from the certification ECU (smart key ECU assembly) requesting a response from the electrical key transmitter sub-assembly is transmitted inside the vehicle. DTC B27A6 is stored by the certification ECU (smart key ECU assembly) when an open is detected between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (rear floor) (between terminals CLG6 and ANTE6, or terminals CG6B and CLGB).
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Note |
|---|---|---|---|---|
|
B27A6 |
Open in Rear Floor Electrical Key Oscillator Circuit |
An open is detected in the circuit between the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (rear floor) (CLG6 - ANTE6, CG6B - CLGB) (1 trip detection logic*). |
|
DTC Output Confirmation Operation:
|
- *: Only output while a malfunction is present.
Vehicle Condition and Fail-safe Operation when Malfunction Detected
|
Vehicle Condition when Malfunction Detected |
Fail-safe Operation when Malfunction Detected |
|---|---|
|
When electrical key transmitter sub-assembly is in rear seat area: |
- |
Related Data List and Active Test
|
DTC No. |
Data List and Active Test |
|---|---|
|
B27A6 |
Key diagnostic mode can be used to perform troubleshooting |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
-
The smart key system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.
Click here
![2018 - 2022 MY Camry [03/2017 - 08/2022]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
-
Before replacing the certification ECU (smart key ECU assembly), refer to Precaution.
Click here
- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
PROCEDURE
|
1. |
CHECK CONNECTOR CONNECTION |
(a) Check that the connectors are properly connected to the certification ECU (smart key ECU assembly) and No. 1 indoor electrical key antenna assembly (rear floor).
OK:
Connectors are properly connected.
| NG |
|
CONNECT CONNECTORS PROPERLY |
|
|
2. |
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)) |
(a) Disconnect the R8 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the R10 No. 1 indoor electrical key antenna assembly (rear floor) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
R8-5 (CLG6) - R10-1 (ANTE6) |
Always |
Below 1 Ω |
|
R8-6 (CG6B) - R10-3 (CLGB) |
Always |
Below 1 Ω |
(d) Reconnect the R8 certification ECU (smart key ECU assembly) connector.
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
3. |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR)) |
|
*a |
Component with harness connected (Certification ECU (Smart Key ECU Assembly)) |
*b |
Waveform |
|
*c |
For 30 seconds after any door closed |
*d |
After 30 seconds or more have elapsed since any door closed |
(a) Using an oscilloscope, check the waveform.
OK:
|
Tester Connection |
Condition |
Tool Setting |
Specified Condition |
|---|---|---|---|
|
R8-5 (CLG6) - K62-18 (E) |
Procedure:
|
2 V/DIV., 500 ms/DIV. |
Pulse generation (See waveform) |
|
R8-6 (CG6B) - K62-18 (E) |
Procedure:
|
2 V/DIV., 500 ms/DIV. |
Pulse generation (See waveform) |
| OK |
|
REPLACE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (REAR FLOOR) |
| NG |
|
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
|
|
|