| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000012VLT |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [03/2017 - 06/2017] |
| Title: CELLULAR COMMUNICATION: SAFETY CONNECT SYSTEM: B1570; Manual (SOS) Switch Red Indicator Malfunction; 2018 MY Camry [03/2017 - 06/2017] | ||
|
DTC |
B1570 |
Manual (SOS) Switch Red Indicator Malfunction |
DESCRIPTION
This DTC is stored when the DCM (Telematics Transceiver) detects an open or short in the manual (SOS) switch red indicator circuit of the manual (SOS) switch.
The manual (SOS) switch red indicator illuminates for 2 seconds and goes off when the engine switch is turned on (IG). If a malfunction in the safety connect system is detected, the manual (SOS) switch red indicator will illuminate.
However, the manual (SOS) switch red indicator may not illuminate when this DTC is set.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
B1570 |
Manual (SOS) Switch Red Indicator Malfunction |
Current for manual (SOS) switch red indicator reaches malfunction criteria for 10 seconds when engine switch is on (IG). |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
HINT:
-
Before performing this diagnostic procedure, make sure to perform Health Check and confirm that the DCM/VIN registration information is correct.
Click here
![2018 - 2019 MY Camry [03/2017 - 09/2019]; CELLULAR COMMUNICATION: SAFETY CONNECT SYSTEM: HEALTH CHECK](/t3Portal/stylegraphics/info.gif)
- The manual (SOS) switch red indicator may not operate to indicate another DTC has been set, therefore voice guidance is provided.
PROCEDURE
|
1. |
CHECK DTC |
(a) Turn the engine switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the engine switch on (IG) and wait for 10 seconds.
(d) Turn the Techstream on.
(e) Clear the DTCs.
Body Electrical > Telematics > Clear DTCs
(f) Recheck for DTCs.
Body Electrical > Telematics > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTC B1570, B1571 and B15C5 are output |
A |
|
DTC B1570 is output (DTC B1571 and B15C5 are not output) |
B |
| B |
|
|
|
2. |
INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (RED INDICATOR) |
|
(a) Disconnect the V14 roof console box sub-assembly connector. |
|
(b) Connect 2 dry-cell batteries (1.5 V each) in series.
(c) Connect the positive (+) lead to terminal 10 (IND1) and the negative (-) lead to terminal 16 (GND3) of the roof console box sub-assembly connector.
(d) Check if the illumination for the manual (SOS) switch red indicator comes on.
OK:
Red indicator comes on.
| NG |
|
|
|
3. |
CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - ROOF CONSOLE BOX SUB-ASSEMBLY) |
(a) Disconnect the K12 DCM (Telematics Transceiver) connector.
(b) Disconnect the V14 roof console box sub-assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K12-26 (SIG-) - V14-16 (GND3) |
Always |
Below 1 Ω |
|
K12-26 (SIG-) or V14-16 (GND3) - Body ground |
Always |
10 kΩ or higher |
|
K12-11 (IND1) - V14-10 (IND1) |
Always |
Below 1 Ω |
|
K12-11 (IND1) or V14-10 (IND1) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
4. |
REPLACE DCM (TELEMATICS TRANSCEIVER) |
(a) Replace the DCM (Telematics Transceiver).
Click here
NOTICE:
- The engine switch must be off.
- Do not swap the DCM (Telematics Transceiver) with one from another vehicle.
| NEXT |
|
|
5. |
CHECK ROOF CONSOLE BOX SUB-ASSEMBLY (MANUAL (SOS) SWITCH RED INDICATOR CONDITION) |
(a) Confirm the red indicator status after the engine switch is turned on (IG).
Click here
|
Result |
Proceed to |
|---|---|
|
Red indicator remains off |
A |
|
Red indicator remains on |
B |
| B |
|
|
|
6. |
INSPECT ROOF CONSOLE BOX SUB-ASSEMBLY (RED INDICATOR INPUT VOLTAGE) |
|
(a) Remove the roof console box sub-assembly but do not disconnect the connectors. Click here
|
|
(b) Connect the positive lead of a voltmeter to terminal V14-10 (IND1), and the negative lead to terminal V14-16 (GND3).
(c) Measure the voltage.
Standard:
1.0 to 8.5 V for 2 seconds after the engine switch is turned on (IG).
0 V when the engine switch is off.
| OK |
|
|
|
7. |
INSPECT TELEMATICS TRANSCEIVER (RED INDICATOR OUTPUT VOLTAGE) |
|
(a) Remove the DCM (Telematics Transceiver) but do not disconnect the connectors. Click here
|
|
(b) Connect the positive lead of a voltmeter to terminal K12-11 (IND1), and the negative lead to body ground.
(c) Measure the voltage.
Standard:
1.0 to 8.5 V for 2 seconds after the engine switch is turned on (IG).
0 V when the engine switch is off.
| OK |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
8. |
CHECK HARNESS AND CONNECTOR (DCM (TELEMATICS TRANSCEIVER) - BODY GROUND) |
|
(a) Remove the DCM (Telematics Transceiver) but do not disconnect the connectors. Click here
|
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
K12-11 (IND1) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
9. |
REPLACE DCM (TELEMATICS TRANSCEIVER) |
(a) Replace the DCM (Telematics Transceiver).
Click here
NOTICE:
- The engine switch must be off.
- Do not swap the DCM (Telematics Transceiver) with one from another vehicle.
| NEXT |
|
|
|