| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000012VFO |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [03/2017 - 06/2017] |
| Title: PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: Buzzer does not Sound; 2018 MY Camry [03/2017 - 06/2017] | ||
|
Buzzer does not Sound |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- When checking for DTCs, make sure that the blind spot monitor system is turned on.
- Inspect the fuses for circuits related to this system before performing the following procedure.
PROCEDURE
|
1. |
CHECK RCTA BUZZER (BLIND SPOT MONITOR BUZZER) |
(a) Check that the RCTA buzzer (blind spot monitor buzzer) sounds when the initial check is performed.
Click here
![2018 MY Camry [03/2017 - 06/2017]; PARK ASSIST / MONITORING: BLIND SPOT MONITOR SYSTEM: SYSTEM DESCRIPTION](/t3Portal/stylegraphics/info.gif)
OK:
RCTA buzzer sounds
| OK |
|
|
|
2. |
CHECK DTC |
(a) Turn the ignition switch off.
(b) Turn the ignition switch to ON.
(c) Recheck for DTCs and check if the same DTC is output again.
Body Electrical > Blind Spot Monitor Slave > Trouble Codes
OK:
No DTCs are output.
| NG |
|
|
|
3. |
CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BLIND SPOT MONITOR SENSOR LH) |
(a) Disconnect the R26 RCTA buzzer (blind spot monitor buzzer) connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
R26-1 (BZP) - Body ground |
Ignition Switch ON |
11 to 14 V |
|
R26-2 (BZN) or W6-3 (BUZ) - Body ground |
Below 1 V |
|
|
R26-2 (BZN) - R26-1 (BZP) |
Below 1 V |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
4. |
CHECK HARNESS AND CONNECTOR (RCTA BUZZER - BLIND SPOT MONITOR SENSOR LH AND BATTERY) |
(a) Disconnect the R26 RCTA buzzer (blind spot monitor buzzer) connector.
(b) Disconnect the W6 blind spot monitor sensor LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
R26-2 (BZN) - W6-3 (BUZ) |
Always |
Below 1 Ω |
|
R26-2 (BZN) or W6-3 (BUZ) - Body ground |
Always |
10 kΩ or higher |
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
R26-2 (BZN) or W6-3 (BUZ) - Body ground |
Ignition Switch ON |
Below 1 V |
|
R26-1 (BZP) - Body ground |
Ignition Switch ON |
11 to 14 V |
|
R26-1 (BZP) - Body ground |
Ignition Switch off |
Below 1 V |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|