Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000012VDJ
Model Year Start: 2018 Model: Camry Prod Date Range: [03/2017 - 06/2017]
Title: A25A-FKS (ENGINE MECHANICAL): REAR CRANKSHAFT OIL SEAL: REMOVAL; 2018 MY Camry [03/2017 - 06/2017]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear crankshaft oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Battery terminal is disconnected/reconnected

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Memorize steering angle neutral point

Parking Assist Monitor System

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

Replacement of ECM

Vehicle Identification Number (VIN) registration

MIL comes on

2018 - 2024 MY Camry [03/2017 -        ]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM: REGISTRATION

ECU communication ID registration (Immobiliser system)

Engine start function

2018 - 2019 MY Camry [03/2017 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION *1

2018 - 2019 MY Camry [03/2017 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: IMMOBILISER SYSTEM (w/o Smart Key System): REGISTRATION *2
  • Gas leak from exhaust system is repaired
  • Replacement of air fuel ratio sensor

Inspection After Repair
  • Poor idle, etc.
  • Engine start function, etc.

2018 - 2019 MY Camry [03/2017 - 09/2019]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION

Replacement of automatic transaxle assembly
  1. Reset memory
  2. Input transaxle compensation code into ECM
  3. Perform road test to allow ECM to learn
  • Large shift shock
  • Deterioration of fuel efficiency

2018 MY Camry [03/2017 - 08/2018]; UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: INITIALIZATION for UB80E Initialization

2018 - 2024 MY Camry [03/2017 -        ]; UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE SYSTEM: REGISTRATION for UB80E Registration

Replacement of ECM

(If possible, read the transaxle compensation code from the previous ECM)
  1. Reset memory*3
  2. Transfer transaxle compensation code
  3. Perform road test to allow ECM to learn

Replacement of ECM

(If impossible, read the transaxle compensation code from the previous ECM)
  1. Reset memory*3
  2. Reset transaxle compensation code
  3. Perform road test to allow ECM to learn

Replacement of ECM*1

Code registration (Smart key System (for Start Function))
  • Wireless door lock control system
  • Smart key system (for Entry Function)
  • Smart key system (for Start Function)
  • Steering lock function

2018 - 2019 MY Camry [03/2017 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function): REGISTRATION

Replacement of ECM*2

Code registration (Immobiliser system (w/o Smart Key System))
  • Wireless door lock control system
  • Engine start

2018 - 2019 MY Camry [03/2017 - 09/2019]; THEFT DETERRENT / KEYLESS ENTRY: IMMOBILISER SYSTEM (w/o Smart Key System): REGISTRATION

Suspension, tires, etc.

(The vehicle height changes because of suspension or tire replacement)

Rear television camera assembly optical axis (Back camera position setting)

Parking assist monitor system

for Initialization: 2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

for Calibration: 2018 MY Camry [03/2017 - 06/2017]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: CALIBRATION

Front wheel alignment adjustment

Perform system variant learning and acceleration sensor zero point calibration.
  • VSC disabled or malfunctioning
  • DTCs are output
  • Slip indicator light illuminated
  • ABS warning light illuminated

2018 MY Camry [03/2017 - 06/2017]; BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS: VEHICLE STABILITY CONTROL SYSTEM: CALIBRATION

  • *1: w/ Smart Key System
  • *2: w/o Smart Key System
  • *3: When the ECM is replaced with a new one, reset memory is unnecessary.

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click here 2018 MY Camry [03/2017 - 06/2017]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

PROCEDURE

1. REMOVE AUTOMATIC TRANSAXLE ASSEMBLY

Click here 2018 MY Camry [03/2017 - 06/2017]; UB80E (AUTOMATIC TRANSMISSION / TRANSAXLE): AUTOMATIC TRANSAXLE ASSEMBLY: REMOVAL

2. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

(a) Using height adjustment attachments and plate lift attachments, place the engine assembly on a flat level surface.

NOTICE:

  • Using height adjustment attachments and plate lift attachments, keep the engine assembly level.
  • To prevent the No. 2 oil pan sub-assembly from deforming, do not place any attachments under the No. 2 oil pan sub-assembly of the engine assembly.
  • Using an engine sling device and engine lift, secure the engine assembly before servicing.

(b) Using SST, hold the crankshaft pulley assembly.

SST: 09213-54015

SST: 09330-00021

(c) Remove the 8 bolts, rear drive plate spacer, drive plate and ring gear sub-assembly.

3. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

(a) Type A:

(1) Remove the No. 1 crankshaft position sensor plate.

(b) Type B:

(1) Remove the No. 1 crankshaft position sensor plate.

4. REMOVE REAR ENGINE OIL SEAL

(a) Using a knife, cut off the lip of the rear engine oil seal.

*a

Protective Tape

*b

Cut Position

(b) Using a screwdriver, pry out the rear engine oil seal.

NOTICE:

Do not damage the surface of the rear engine oil seal press fit hole or the crankshaft.

HINT:

Tape the screwdriver tip before use.