Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000012V75
Model Year Start: 2018 Model: Camry Prod Date Range: [03/2017 -           ]
Title: A25A-FKS (ENGINE CONTROL): THROTTLE BODY: ON-VEHICLE INSPECTION; 2018 - 2024 MY Camry [03/2017 -        ]

ON-VEHICLE INSPECTION

PROCEDURE

1. INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY

(a) Before cleaning, or after cleaning the throttle body with motor assembly and installing it to the vehicle, turn the ignition switch to ON without operating the accelerator pedal sensor assembly.

NOTICE:

If the accelerator pedal sensor assembly has been operated, restart the procedure from the step above.

(b) Connect the Techstream to the DLC3 and check for DTCs. If DTCs are stored, repair them by following the repair procedure flow. If DTCs are not stored, perform the throttle body operation check.

(c) Check throttle body operation.

(1) Enter the following menus:

Powertrain / Engine / Active Test / Control the ETCS Open/Close Slow Speed

(2) During Active Test operation, check the Data List items "Throttle Position Command" and "Throttle Position Sensor No. 1 Voltage".

Powertrain > Engine > Active Test

Active Test Display

Control the ETCS Open/Close Slow Speed

Data List Display

Throttle Position Sensor No.1 Voltage

Throttle Position Command

*a

Correct

*b

Incorrect

*c

Throttle Position Command

*d

Throttle Position Sensor No.1 Voltage

*e

Specified Condition

*f

200 ms

OK:

Tester Display

Condition

Specified Condition

Throttle Position Command

Throttle Position Sensor No.1 Voltage

Checked during Active Test operation at a voltage of 1.3 V to 2.1 V.

Response lag between Throttle Position Command and Throttle Position Sensor No. 1 Voltage is within 200 ms.

(3) Enter the following menus:

Powertrain / Engine / Active Test / Control the ETCS Open/Close Fast Speed

(4) During Active Test operation, check the Data List items "Throttle Position Command" and "Throttle Position Sensor No. 1 Voltage".

Powertrain > Engine > Active Test

Active Test Display

Control the ETCS Open/Close Fast Speed

Data List Display

Throttle Position Sensor No.1 Voltage

Throttle Position Command

*a

Correct

*b

Incorrect

*c

Throttle Position Command

*d

Throttle Position Sensor No.1 Voltage

*e

Specified Condition

*f

200 ms

OK:

Tester Display

Condition

Specified Condition

Throttle Position Command

Throttle Position Sensor No.1 Voltage

Checked during Active Test operation at a voltage of 1.3 V to 2.1 V.

Response lag between Throttle Position Command and Throttle Position Sensor No. 1 Voltage is within 200 ms.

(d) Warm up the engine.

NOTICE:

  • The A/C switch and all accessory switches should be off.
  • The electric fan should be off.
  • After warming up the engine, check that the coolant temperature is 75° C or more.

(e) Check the "Throttle Position Sensor No.1 Voltage %".

(1) Read the Data List while quickly and fully depressing the accelerator pedal and check that the value for "Throttle Position Sensor No.1 Voltage %" is 60% or more.

(f) If there was any abnormality found during the throttle body operation check or "Throttle Position Sensor No.1 Voltage %" check, clean the throttle body, then reassemble it and perform the throttle body operation check again. If the operation returns to normal, the procedure is complete. If operation does not return to normal, replace the throttle body with motor assembly.

(g) Perform "Inspection After Repair" after replacing or cleaning the throttle body with motor assembly.

Click here 2018 - 2019 MY Camry [03/2017 - 09/2019]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION 2020 MY Camry [09/2019 - 03/2020]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION 2020 - 2024 MY Camry [03/2020 -        ]; A25A-FKS (ENGINE CONTROL): SFI SYSTEM: INITIALIZATION