Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000012UQL
Model Year Start: 2018 Model: Camry Prod Date Range: [03/2017 -           ]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: B162B,B162C,B1694; Side Airbag Sensor Assembly No.2 Lost Communication (RH); 2018 - 2024 MY Camry [03/2017 -        ]

DTC

B162B

Side Airbag Sensor Assembly No.2 Lost Communication (RH)

DTC

B162C

Side Airbag Sensor Assembly No.2 Initialization Error (RH)

DTC

B1694

No.2 Side Satellite Sensor Bus RH Initialization Incomplete

DESCRIPTION

The side collision sensor RH circuit (bus 2) consists of the airbag sensor assembly and side No. 1 airbag sensor RH.

The side No. 1 airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbags and pretensioners should be deployed.

These DTCs are stored when a malfunction is detected in the side collision sensor RH circuit (bus 2).

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

Test Mode / Check Mode

B162B

Side Airbag Sensor Assembly No.2 Lost Communication (RH)

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 2).
  • Side No. 1 airbag sensor RH malfunction
  • Airbag sensor assembly malfunction
  • Floor wire
  • Side No. 1 airbag sensor RH
  • Airbag sensor assembly

Comes on

Does not apply to test/check mode

B162C

Side Airbag Sensor Assembly No.2 Initialization Error (RH)

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 2).
  • Side No. 1 airbag sensor RH malfunction
  • Airbag sensor assembly malfunction
  • Floor wire
  • Side No. 1 airbag sensor RH
  • Airbag sensor assembly

Comes on

Does not apply to test/check mode

B1694

No.2 Side Satellite Sensor Bus RH Initialization Incomplete

  • The airbag sensor assembly detects a line short, short to ground or B+, or an open in the side collision sensor RH circuit (bus 2).
  • Side No. 1 airbag sensor RH malfunction
  • Airbag sensor assembly malfunction
  • Floor wire
  • Side No. 1 airbag sensor RH
  • Airbag sensor assembly

Comes on

Does not apply to test/check mode

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2018 MY Camry [03/2017 - 06/2017]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2018 - 2019 MY Camry [06/2017 - 09/2019]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION 2020 - 2024 MY Camry [03/2020 -        ]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

PROCEDURE

1.

CHECK CONNECTION OF CONNECTORS

(a) Turn the ignition switch off.

(b) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Check that the connectors are properly connected to the airbag sensor assembly and side No. 1 airbag sensor RH.

OK:

The connectors are properly connected.

NG

CONNECT CONNECTORS PROPERLY

OK

2.

CHECK CONNECTORS

(a) Disconnect the connectors from the airbag sensor assembly and side No. 1 airbag sensor RH.

(b) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

NG

REPLACE FLOOR WIRE

OK

3.

CHECK FLOOR WIRE

(a) Connect the cable to the negative (-) battery terminal.

*1

Side No. 1 Airbag Sensor RH

*2

Airbag Sensor Assembly

*3

Floor Wire

*4

Service Wire

*a

Front view of wire harness connector

(to Airbag Sensor Assembly)

*b

Front view of wire harness connector

(to Side No. 1 Airbag Sensor RH)

(b) Turn the ignition switch to ON.

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Condition

Specified Condition

R35-2 (BFR+) - Body ground

Ignition switch ON

Below 1 V

R35-1 (BFR-) - Body ground

Ignition switch ON

Below 1 V

(d) Turn the ignition switch off.

(e) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(f) Using a service wire, connect terminals 28 (BCR+) and 27 (BCR-) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

(g) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

R35-2 (BFR+) - R35-1 (BFR-)

Always

Below 1 Ω

(h) Disconnect the service wire from connector B.

(i) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

R35-2 (BFR+) - R35-1 (BFR-)

Always

1 MΩ or higher

R35-2 (BFR+) - Body ground

Always

1 MΩ or higher

R35-1 (BFR-) - Body ground

Always

1 MΩ or higher

NG

REPLACE FLOOR WIRE

OK

4.

CHECK SIDE NO. 1 AIRBAG SENSOR RH

(a) Connect the connector to the airbag sensor assembly.

*1

Side No. 1 Airbag Sensor LH

*2

Airbag Sensor Assembly

(b) Interchange the side No. 1 airbag sensor RH with LH and connect the connectors.

(c) Connect the cable to the negative (-) battery terminal.

(d) Turn the ignition switch to ON, and wait for at least 60 seconds.

(e) Clear the DTCs stored in memory.

Body Electrical > SRS Airbag > Clear DTCs

(f) Turn the ignition switch off.

(g) Turn the ignition switch to ON, and wait for at least 60 seconds.

(h) Check for DTCs.

Body Electrical > SRS Airbag > Trouble Codes

HINT:

Codes other than DTCs B162B, B162C, B163B, B163C, B1694 and B1699 may be output at this time, but they are not related to this check.

Result

Proceed to

DTC B162B, B162C or B1694 is output.

A

DTC B163B, B163C or B1699 is output.

B

DTCs B162B, B162C, B163B, B163C, B1694 and B1699 are not output.

C

(i) Turn the ignition switch off.

(j) Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(k) Return the side No. 1 airbag sensor RH and LH to their original positions and connect the connectors.

A

REPLACE AIRBAG SENSOR ASSEMBLY 2018 MY Camry [03/2017 - 06/2017]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2018 - 2019 MY Camry [06/2017 - 09/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2020 MY Camry [09/2019 - 03/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2020 MY Camry [03/2020 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: CENTER AIRBAG SENSOR ASSEMBLY: REMOVAL

B

REPLACE SIDE NO. 1 AIRBAG SENSOR RH 2018 MY Camry [03/2017 - 06/2017]; SUPPLEMENTAL RESTRAINT SYSTEMS: SIDE AIRBAG SENSOR (for Center Pillar): REMOVAL 2018 - 2019 MY Camry [06/2017 - 09/2019]; SUPPLEMENTAL RESTRAINT SYSTEMS: SIDE AIRBAG SENSOR (for Center Pillar): REMOVAL 2020 MY Camry [09/2019 - 10/2020]; SUPPLEMENTAL RESTRAINT SYSTEMS: SIDE AIRBAG SENSOR (for Center Pillar): REMOVAL 2021 - 2024 MY Camry [10/2020 -        ]; SUPPLEMENTAL RESTRAINT SYSTEMS: SIDE AIRBAG SENSOR (for Center Pillar): REMOVAL

C

USE SIMULATION METHOD TO CHECK 2018 MY Camry [03/2017 - 06/2017]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2018 MY Camry [06/2017 - 08/2018]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2019 MY Camry [08/2018 - 09/2019]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry [09/2019 - 03/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2020 MY Camry [03/2020 - 10/2020]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2021 MY Camry [10/2020 - 08/2021]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING 2022 - 2024 MY Camry [08/2021 -        ]; INTRODUCTION: HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS: HOW TO PROCEED WITH TROUBLESHOOTING