| Last Modified: 11-20-2023 | 6.11:8.1.0 | Doc ID: RM1000000012UOL |
| Model Year Start: 2018 | Model: Camry | Prod Date Range: [03/2017 - 06/2017] |
| Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: B150819; Turn Signal/Hazard Flasher Circuit Current Above Threshold; 2018 MY Camry [03/2017 - 06/2017] | ||
|
DTC |
B150819 |
Turn Signal/Hazard Flasher Circuit Current Above Threshold |
DESCRIPTION
This DTC is stored when the combination meter assembly detects an short in a turn signal light circuit.
HINT:
If there is a short in a turn signal light circuit, all of the turn signal lights on the side with the short circuit will not blink.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Memory |
Note |
|---|---|---|---|---|---|
|
B150819 |
Turn Signal/Hazard Flasher Circuit Current Above Threshold |
Diagnosis Condition:
Malfunction Status:
|
|
DTC stored |
- |
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
-
Inspect the turn signal light bulbs, sockets and wire harnesses before performing the following procedure.
Side turn signal light assembly: Click here
![2018 - 2024 MY Camry [03/2017 - ]; LIGHTING (EXT): SIDE TURN SIGNAL LIGHT ASSEMBLY: INSPECTION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
|
1. |
INSPECT LIGHTS |
(a) Inspect the illumination of each turn signal light.
|
Result |
Proceed to |
|---|---|
|
All LH turn signal lights do not blink |
A |
|
All RH turn signal lights do not blink |
B |
| B |
|
|
|
2. |
CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY LH - COMBINATION METER ASSEMBLY) |
(a) Disconnect the W13 rear combination light assembly LH connector.
(b) Disconnect the K20 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
W13-3 (B) or K20-10 (TRNL) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
3. |
CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - COMBINATION METER ASSEMBLY) |
(a) Disconnect the 3A instrument panel junction block assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
3A-5 or K20-11 (LL) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
4. |
CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
(a) Disconnect the A53 headlight assembly LH connector.
(b) Disconnect the 3C instrument panel junction block assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A53-1 (B) or 3C-6 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
5. |
CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY LH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
(a) Disconnect the O20 side turn signal light assembly LH connector.
(b) Disconnect the 3D instrument panel junction block assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
O20-5 (B) or 3D-14 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
6. |
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
|
*a |
Component without harness connected (Instrument Panel Junction Block Assembly) |
- |
- |
(a) Measure the resistance according to the value(s) in the table below.
NOTICE:
Make sure to perform this step with the instrument panel junction block assembly installed to the vehicle.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
3C-6, 3D-14 or 3A-5 - Body ground |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
|
7. |
CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT ASSEMBLY RH - COMBINATION METER ASSEMBLY) |
(a) Disconnect the W12 rear combination light assembly RH connector.
(b) Disconnect the K20 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
W12-3 (B) or K20-13 (TRNR) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
8. |
CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - COMBINATION METER ASSEMBLY) |
(a) Disconnect the 3A instrument panel junction block assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
3A-4 or K20-7 (LR) - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
9. |
CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
(a) Disconnect the A52 headlight assembly RH connector.
(b) Disconnect the 3C instrument panel junction block assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A52-1 (B) or 3C-8 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
10. |
CHECK HARNESS AND CONNECTOR (SIDE TURN SIGNAL LIGHT ASSEMBLY RH - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
(a) Disconnect the N18 side turn signal light assembly RH connector.
(b) Disconnect the 3D instrument panel junction block assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
N18-5 (B) or 3D-16 - Body ground |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
11. |
INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY |
|
*a |
Component without harness connected (Instrument Panel Junction Block Assembly) |
- |
- |
(a) Measure the resistance according to the value(s) in the table below.
NOTICE:
Make sure to perform this step with the instrument panel junction block assembly installed to the vehicle.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
3C-8, 3D-16 or 3A-4 - Body ground |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
|
|