Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000012UH6
Model Year Start: 2018 Model: Camry Prod Date Range: [03/2017 - 06/2017]
Title: LIGHTING (INT): LIGHTING SYSTEM: OPERATION CHECK; 2018 MY Camry [03/2017 - 06/2017]

OPERATION CHECK

INSPECT ILLUMINATED ENTRY SYSTEM OPERATION

NOTICE:

Perform this inspection with the customize parameters at the initial settings.

HINT:

Perform this inspection with the door linked switch of the map light (roof console box sub-assembly) on*1 or the switch of the room light assembly in the DOOR position*2.

  • *1: w/ Room Light (for LED Type)
  • *2: w/ Room Light (for Bulb Type)

Control

Condition

Lights that Operate

Actuation Area-linked*1

With the engine switch off and all of the doors closed and locked, enter an exterior detection area while carrying an electrical key transmitter and check that the lights that operate turn on for approximately 15 seconds and then turn off.
  • Map Light (Roof Console Box Sub-assembly)*3
  • Spot Light Assembly*3
  • Room Light Assembly*4

Door Lock/Unlock-linked

With the ignition switch off and all of the doors closed and locked, unlock any door using an unlock operation (key-linked, wireless or entry unlock operation) and check that the lights that operate turn on for 15 seconds and then turn off.
  • Ignition Key Cylinder Light (Transponder Key Coil)*2
  • Map Light (Roof Console Box Sub-assembly)*3
  • Spot Light Assembly*3
  • Room Light Assembly*4

Door Open/Close-linked

With the ignition switch off and all of the doors closed, open any door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off after approximately 15 seconds.
  • Ignition Key Cylinder Light (Transponder Key Coil)*2
  • Map Light (Roof Console Box Sub-assembly)*3
  • Spot Light Assembly*3
  • Room Light Assembly*4

With the engine switch off and all of the doors closed, open any door and check that the light that operates turns on. While the light that operates is on, close all of the doors and check that the light that operates turns off after approximately 40 seconds.

Engine Switch Illumination*1

With the ignition switch in ON, open any door and check that the lights that operate turn on. While the lights that operate are on, close all of the doors and check that the lights that operate turn off.
  • Ignition Key Cylinder Light (Transponder Key Coil)*2
  • Map Light (Roof Console Box Sub-assembly)*3
  • Spot Light Assembly*3
  • Room Light Assembly*4

Engine Switch-linked*1

Turn the engine switch from on (ACC) or on (IG) to off and check that the lights that operate turn on for approximately 15 seconds and then turn off.
  • Map Light (Roof Console Box Sub-assembly)*3
  • Spot Light Assembly*3
  • Room Light Assembly*4

Turn the engine switch from on (ACC) or on (IG) to off and check that the light that operates turns on for approximately 40 seconds and then turns off.

Engine Switch Illumination

Ignition Switch-linked*2

Turn the ignition switch from ACC or ON to off and check that the lights that operate turn on for approximately 15 seconds and then turn off.
  • Ignition Key Cylinder Light (Transponder Key Coil)*2
  • Map Light (Roof Console Box Sub-assembly)*3
  • Spot Light Assembly*3
  • Room Light Assembly*4
  • *1: w/ Smart Key System
  • *2: w/o Smart Key System
  • *3: w/ Room Light (for LED Type)
  • *4: w/ Room Light (for Bulb Type)

INSPECT BATTERY SAVING CONTROL OPERATION

(a) The operations and conditions of this control are described below.

Control

Condition

Lights that Operate

Basic operation

When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off.

HINT:

Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.

  • The ignition switch is turned ACC or ON.
  • Any door is opened and closed.
  • The luggage compartment door is opened and closed.
  • Any door is unlocked.
  • The key enters any exterior actuation area.*1
  • Engine Switch Illumination*1
  • Ignition Key Cylinder Light (Transponder Key Coil)*2
  • Map Light (Roof Console Box Sub-assembly)*3
  • Spot Light Assembly*3
  • Room Light Assembly*4

Interior light auto cut operation

When 20 minutes elapse after the ignition switch is turned from ACC or ON to off and the lights that operate remain on, the lights are turned off.

HINT:

Battery saving control is canceled when any of the following operations is performed before the lights are turned off by battery saving control. After the operation is performed, the lights remain on for another 20 minutes and then the lights are turned off.

  • The ignition switch is turned ACC or ON.
  • Map Light (Roof Console Box Sub-assembly)*3
  • Spot Light Assembly*3
  • Room Light Assembly*4
  • Vanity Light Assembly*5
  • No. 1 Luggage Compartment Light Assembly
  • Courtesy Light Assembly
  • *1: w/ Smart Key System
  • *2: w/o Smart Key System
  • *3: w/ Room Light (for LED Type)
  • *4: w/ Room Light (for Bulb Type)
  • *5: w/ Vanity Light