Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM1000000012TWW |
Model Year Start: 2018 |
Model: Camry |
Prod Date Range: [03/2017 -
] |
Title: SLIDING ROOF / CONVERTIBLE: SLIDING ROOF SYSTEM: B2341,B2344; Sensor (Motor) Failure; 2018 - 2024 MY Camry [03/2017 - ] |
DTC
|
B2341
|
Sensor (Motor) Failure
|
DTC
|
B2344
|
Position Failure
|
DESCRIPTION
When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a motor malfunction and the sliding roof operation is stopped, DTC B2341 is stored.
When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a gear position malfunction and the sliding roof operation is stopped, DTC B2344 is stored.
DTC No.
|
Detection Item
|
DTC Detection Condition
|
Trouble Area
|
B2341
|
Sensor (Motor) Failure
|
Sensor (motor) failure (The sliding roof ECU (sliding roof drive gear sub-assembly) enters fail-safe mode due to a problem with the motor)
|
-
Sliding roof ECU (Sliding roof drive gear sub-assembly)
-
Sliding roof switch (Roof console box sub-assembly)
-
Wire harness or connector
|
B2344
|
Position Failure
|
Position failure (The sliding roof ECU (sliding roof drive gear sub-assembly) enters fail-safe mode due to a problem with the gear position)
|
-
Sliding roof ECU (Sliding roof drive gear sub-assembly)
-
Sliding roof switch (Roof console box sub-assembly)
-
Wire harness or connector
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
If the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized.
Click here
PROCEDURE
1.
|
CHECK SLIDING ROOF OPERATION
|
(a) Check the sliding roof auto operation.
Click here
OK:
Auto operation operates normally.
OK
|
|
|
(a) Clear the DTCs.
Body Electrical > Sliding Roof > Clear DTCs
(b) Check for DTCs.
Body Electrical > Sliding Roof > Trouble Codes
OK:
DTCs B2341 and B2344 are not output.
3.
|
INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)
|
(a) Check that the sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.
Click here
OK:
Sliding roof ECU (sliding roof drive gear sub-assembly) can be initialized.
OK
|
|
|
(a) Clear the DTCs.
Body Electrical > Sliding Roof > Clear DTCs
(b) Check for DTCs.
Body Electrical > Sliding Roof > Trouble Codes
OK:
DTCs B2341 and B2344 are not output.
OK |
|
END (MALFUNCTION DUE TO INITIALIZATION FAILURE)
|
5.
|
CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY) - SLIDING ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY) AND BODY GROUND)
|
(a) Disconnect the V14 sliding roof switch (roof console box sub-assembly) connector.
(b) Disconnect the V2 sliding roof ECU (sliding roof drive gear sub-assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
V2-8 (CLS) - V14-4 (CLS)
|
Always
|
Below 1 Ω
|
V2-8 (CLS) or V14-4 (CLS) - Body ground
|
Always
|
10 kΩ or higher
|
V2-10 (OPN) - V14-5 (OPN)
|
Always
|
Below 1 Ω
|
V2-10 (OPN) or V14-5 (OPN) - Body ground
|
Always
|
10 kΩ or higher
|
V2-9 (CLS) - V14-18 (DOWN)
|
Always
|
Below 1 Ω
|
V2-9 (CLS) or V14-18 (DOWN) - Body ground
|
Always
|
10 kΩ or higher
|
V2-5 (OPN) - V14-3 (UP)
|
Always
|
Below 1 Ω
|
V2-5 (OPN) or V14-3 (UP) - Body ground
|
Always
|
10 kΩ or higher
|
V14-15 (GND) - Body ground
|
Always
|
Below 1 Ω
|
V2-2 (E) - Body ground
|
Always
|
Below 1 Ω
|
NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR
|
OK
|
|
|
6.
|
INSPECT SLIDING ROOF SWITCH (ROOF CONSOLE BOX SUB-ASSEMBLY)
|
(a) Remove the sliding roof switch (roof console box sub-assembly).
Click here
(b) Inspect the sliding roof switch (roof console box sub-assembly).
Click here
|