Last Modified: 11-20-2023 |
6.11:8.1.0 |
Doc ID: RM1000000012TWA |
Model Year Start: 2018 |
Model: Camry |
Prod Date Range: [03/2017 - 06/2017] |
Title: PARKING BRAKE: PARKING BRAKE CABLE (for Front Side): REMOVAL; 2018 MY Camry [03/2017 - 06/2017] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during No. 1 parking brake cable assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Disconnect cable from negative battery terminal
|
Perform steering sensor zero point calibration
|
Lane departure alert system (w/ Steering Control)
|
|
Pre-collision system
|
Memorize steering angle neutral point
|
Parking assist monitor system
|
|
Removal/installation of the front passenger seat
|
Zero point calibration (Occupant classification system)
|
-
Occupant classification system
-
Passenger airbag ON/OFF indicator
-
Airbag system (Front passenger side)
-
Seat belt warning system (Front passenger)
|
|
PROCEDURE
1. REMOVE PARKING BRAKE PEDAL ASSEMBLY
Click here
2. REMOVE FRONT SEAT ASSEMBLY LH
Click here
3. REMOVE FRONT SEAT ASSEMBLY RH
Click here
4. REMOVE CONSOLE BOX ASSEMBLY
Click here
5. DISCONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY
Click here
6. REMOVE REAR SEAT CUSHION ASSEMBLY
Click here
7. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
8. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Click here
9. REMOVE REAR DOOR SCUFF PLATE LH
Click here
10. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH
Click here
11. REMOVE LOWER CENTER PILLAR GARNISH LH
Click here
12. REMOVE FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
13. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
HINT:
Use the same procedure as for the LH side.
14. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
15. REMOVE REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedure as for the LH side.
16. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH
HINT:
Use the same procedure as for the LH side.
17. REMOVE LOWER CENTER PILLAR GARNISH RH
HINT:
Use the same procedure as for the LH side.
18. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Click here
19. REMOVE ACCELERATOR PEDAL
Click here
20. REMOVE FRONT FLOOR CAUTION PLATE COVER
Click here
21. DISCONNECT FRONT FLOOR CARPET ASSEMBLY
(a) for LH Side:
(1) Using a clip remover, remove the 2 front floor carpet clips.
|
Fastener
|
-
|
-
|
(2) Disengage the 3 guides.
(3) Disengage each fastener and turn back the front floor carpet assembly as shown in the illustration.
(b) for RH Side:
(1) Using a clip remover, remove the 2 front floor carpet clips.
(2) Disengage the 3 guides.
(3) Turn back the front floor carpet assembly as shown in the illustration.
22. REMOVE REAR NO. 2 AIR DUCT
(a) Disengage the 4 claws to remove the rear No. 2 air duct as shown in the illustration.
|
Remove in this Direction
|
23. REMOVE REAR NO. 1 AIR DUCT
Click here
24. REMOVE NO. 1 CONSOLE BOX DUCT (for Dual Type)
(a) Remove the clip.
|
Remove in this Direction
|
(b) Remove the No. 1 console box duct as shown in the illustration.
25. REMOVE NO. 2 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY (w/ Smart Key System)
Click here
26. SEPARATE NO. 1 PARKING BRAKE CABLE ASSEMBLY
(a) Separate the No. 1 parking brake cable assembly from the No. 1 parking brake pull rod sub-assembly as shown in the illustration.
|
|
27. REMOVE BRAKE PEDAL SUPPORT ASSEMBLY
Click here
28. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY
(a) Disengage the 4 clamps.
|
|
(b) Remove the 2 nuts, and separate the brake pedal support base from the vehicle body.
NOTICE:
Do not damage the air conditioner unit assembly when separating the brake pedal support base from the vehicle.
HINT:
Separate the brake pedal support base just enough to gain access to the nut of the No. 1 parking brake cable assembly.
(d) Remove the 3 bolts, nut and No. 1 parking brake cable assembly.
|
|
|