Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000012TM4
Model Year Start: 2018 Model: Camry Prod Date Range: [03/2017 - 06/2017]
Title: EXTERIOR PANELS / TRIM: REAR DOOR WINDOW FRAME MOULDING: REMOVAL; 2018 MY Camry [03/2017 - 06/2017]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during rear door window frame moulding removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane departure alert system (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Memorize steering angle neutral point

Parking assist monitor system

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

  • Rear door glass sub-assembly
  • Rear door glass run

Initialize power window control system

  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Wireless transmitter-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

2018 - 2024 MY Camry [03/2017 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. REMOVE REAR DOOR BELT MOULDING ASSEMBLY

Click here 2018 MY Camry [03/2017 - 06/2017]; EXTERIOR PANELS / TRIM: REAR DOOR BELT MOULDING: REMOVAL

2. DISCONNECT REAR DOOR WEATHERSTRIP

(a) Disengage the 2 clips and disconnect the rear door weatherstrip.

3. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING

HINT:

When removing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.

Heating Temperature

Item

Temperature

Vehicle Body

40 to 60°C (104 to 140°F)

Rear Door Front Window Frame Moulding

20 to 30°C (68 to 86°F)

CAUTION:

  • Do not touch the heat light and heated parts, touching the heat light may result in burns.
  • Touching heated parts for a long time may result in burns.

*a

Heated Part

*b

Heat Light

NOTICE:

Do not heat the vehicle body or rear door front window frame moulding excessively.

(a) Using a heat light, heat the rear door front window frame moulding.

(b) Using a moulding remover, disengage the clip and separate the double-sided tape and caulking sponge to remove the rear door front window frame moulding.

*a

Double-sided Tape

*b

Caulking Sponge

4. REMOVE REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY

(a) Insert a 4.0 mm (0.157 in.) drill bit into a drill.

(b) Tape the 4.0 mm (0.157 in.) drill bit 5.0 mm (0.197 in.) from the tip as shown in the illustration.

Standard Measurement:

Area

Measurement

A

5.0 mm (0.197 in.)

NOTICE:

Tape the 4.0 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

*a

Tape

(c) Lightly press the drill bit against the rivets to drill off the rivet flanges, and remove the 6 rivets.

CAUTION:

Be careful of the drilled rivets, as they may be hot.

NOTICE:

  • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
  • Prying the rivets with the drill may damage the rivet installation holes or drill bit.

(d) Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

(e) Disengage the clip, 2 claws and guide to remove the rear door window frame moulding sub-assembly.