Last Modified: 11-20-2023 6.11:8.1.0 Doc ID: RM1000000012TL1
Model Year Start: 2018 Model: Camry Prod Date Range: [03/2017 - 06/2017]
Title: WINDOW / GLASS: POWER WINDOW REGULATOR MOTOR (for Front Door): REMOVAL; 2018 MY Camry [03/2017 - 06/2017]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during power window regulator motor assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure

Necessary Procedure

Effect/Inoperative Function when Necessary Procedure not Performed

Link

Disconnect cable from negative battery terminal

Perform steering sensor zero point calibration

Lane Departure Alert System (w/ Steering Control)

2018 - 2020 MY Camry [03/2017 - 10/2020]; PRE-COLLISION: PRE-COLLISION SYSTEM: INITIALIZATION

Pre-collision system

Memorize steering angle neutral point

Parking Assist Monitor System

2018 - 2024 MY Camry [03/2017 -        ]; PARK ASSIST / MONITORING: PARKING ASSIST MONITOR SYSTEM: INITIALIZATION

  • Door window regulator assembly
  • Power window regulator motor assembly
  • Door glass
  • Door glass run

Initialize power window control system
  • Auto up and down function
  • Jam protection function
  • Remote control function
  • Key-linked function
  • Wireless transmitter-linked function
  • Key-off operation function
  • Catch protection function
  • Window open warning function

2018 - 2024 MY Camry [03/2017 -        ]; WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: INITIALIZATION

HINT:

  • Use the same procedure for the RH side and LH side.
  • The following procedure is for the LH side.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2018 MY Camry [03/2017 - 06/2017]; INTRODUCTION: REPAIR INSTRUCTION: PRECAUTION

2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Click here 2018 MY Camry [03/2017 - 06/2017]; MAINTENANCE: A25A-FKS BATTERY: REMOVAL+

3. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

Click here 2018 MY Camry [03/2017 - 06/2017]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

4. REMOVE FRONT DOOR ARMREST COVER SUB-ASSEMBLY

Click here 2018 MY Camry [03/2017 - 06/2017]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

5. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Driver Side)

Click here 2018 MY Camry [03/2017 - 06/2017]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

6. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR UPPER ARMREST BASE PANEL (for Front Passenger Side)

Click here 2018 MY Camry [03/2017 - 06/2017]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

7. REMOVE FRONT ARMREST ASSEMBLY

Click here 2018 MY Camry [03/2017 - 06/2017]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

8. REMOVE COURTESY LIGHT ASSEMBLY

Click here 2018 - 2024 MY Camry [03/2017 -        ]; LIGHTING (INT): DOOR COURTESY LIGHT: REMOVAL+

9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Click here 2018 MY Camry [03/2017 - 06/2017]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

10. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP WITH FRONT DOOR VENT SEAL

Click here 2018 MY Camry [03/2017 - 06/2017]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

11. REMOVE FRONT DOOR SERVICE HOLE COVER

Click here 2018 MY Camry [03/2017 - 06/2017]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

12. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Click here 2018 MY Camry [03/2017 - 06/2017]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

13. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

Click here 2018 MY Camry [03/2017 - 06/2017]; DOOR / HATCH: FRONT DOOR: DISASSEMBLY+

14. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

(a) Using a T25 "TORX" socket wrench, remove the 3 screws and power window regulator motor assembly.